ADG1401BCPZ-REEL7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 weeks ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-WFDFN Exposed Pad, CSP |
| Number of Pins | 8 |
| Supplier Device Package | 8-LFCSP-WD (2x3) |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Resistance | 1.3Ohm |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -40°C |
| Max Power Dissipation | 1.44mW |
| Base Part Number | ADG1401 |
| Number of Outputs | 1 |
| Operating Supply Voltage | 12V |
| Number of Channels | 1 |
| Interface | Parallel |
| Number of Circuits | 1 |
| Max Supply Voltage | 16.5V |
| Min Supply Voltage | 5V |
| Test Frequency | 1MHz |
| Power Dissipation | 1.44mW |
| Max Supply Current | 95μA |
| Turn On Delay Time | 150 ns |
| Number of Inputs | 1 |
| Voltage - Supply, Single/Dual (±) | 5V~16.5V ±4.5V~16.5V |
| Supply Type | Dual, Single |
| Bandwidth | 120MHz |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 16.5V |
| -3db Bandwidth | 120MHz |
| On-State Resistance (Max) | 1.3Ohm |
| Min Dual Supply Voltage | 4.5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 400pA |
| Channel Capacitance (CS(off), CD(off)) | 36pF 41pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Insertion Loss (dB) | 0.08 dB |
| Charge Injection | -12pC |
| Channel-to-Channel Matching (ΔRon) | 200mOhm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG1401BCPZ-REEL7 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 8-WFDFN Exposed Pad, CSP. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. It is mounted in the position Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. Extended operating temperature around -40°C~125°C TA. A electrical component with 1 channels is capable of high-quality output. Based on SPST - NO switching circuits, these analog multiplexers work. A 1 circuit is present in this switch device. Using the ADG1401 search parameter, you can discover variants of the switch. An switch multiplexer with 1.3Ohm internal resistance has a value of 1.3Ohm. For details about the functions of 8 pins, please refer to the datasheets. A voltage higher than 16.5V should not normally be supplied to the switches. The digital multiplexer has a low cost Dual, Single supply. 5V is the lowest voltage the electrical component should receive. A voltage higher than 95μA may cause damage to the switch multiplexer. For this switch, a dual supply voltage is feasible, but it must not exceed 16.5VIn the case of dual power supplies, you should connect at least 4.5V. The electronic component can function from 12V. In order to operate the 1 inputs, there are several steps to follow. 120MHz-bandwidths can be used to transfer data between multiplexers. Temperatures higher than 125°C are not recommended for operation of the analogue multiplexer. The analogue multiplexer has 1 outputs. Suppliers offer 8-LFCSP-WD (2x3) packages.
ADG1401BCPZ-REEL7 Features
1 Channels
Switch Circuit: SPST - NO
-3db Bandwidth: 120MHz
Bandwidth: 120MHz
ADG1401BCPZ-REEL7 Applications
There are a lot of Analog Devices Inc. ADG1401BCPZ-REEL7 Analog Switches & Multiplexers ICs applications.
- Battery-powered systems
- Cross Connects
- Audio and video switching
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Signal routing between systems
- PDH Multiplexers
- Sample hold systems
- Isolation
- Optical Applications
- Fiber to the Home
