Parameters |
Min Dual Supply Voltage |
4.5V |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
58 dB |
Current - Leakage (IS(off)) (Max) |
400pA |
Channel Capacitance (CS(off), CD(off)) |
36pF 41pF |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
150ns, 150ns |
Insertion Loss (dB) |
0.08 dB |
Charge Injection |
-12pC |
Channel-to-Channel Matching (ΔRon) |
200m Ω |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
375ns |
Normal Position |
NC |
Length |
3mm |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 1 week ago) |
Mounting Type |
Surface Mount |
Package / Case |
8-WFDFN Exposed Pad, CSP |
Surface Mount |
YES |
Number of Pins |
8 |
Operating Temperature |
-40°C~125°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e3 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
ECCN Code |
EAR99 |
Resistance |
1.3Ohm |
Terminal Finish |
MATTE TIN |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
1.44mW |
Technology |
CMOS |
Terminal Form |
NO LEAD |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
5V |
Terminal Pitch |
0.5mm |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
ADG1402 |
Pin Count |
8 |
Qualification Status |
Not Qualified |
Operating Supply Voltage |
12V |
Number of Channels |
1 |
Interface |
Parallel |
Max Supply Voltage |
16.5V |
Min Supply Voltage |
5V |
Test Frequency |
1MHz |
Power Dissipation |
1.44mW |
Max Supply Current |
95μA |
Turn On Delay Time |
150 ns |
Number of Inputs |
1 |
Voltage - Supply, Single/Dual (±) |
5V~16.5V ±4.5V~16.5V |
Supply Type |
Dual, Single |
Bandwidth |
120MHz |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Turn-Off Delay Time |
150 ns |
Max Dual Supply Voltage |
16.5V |
On-State Resistance (Max) |
1.3Ohm |
ADG1402BCPZ-REEL7 Overview
Due to its 8-WFDFN Exposed Pad, CSP packaging, the electronic part is convenient for international shipping. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. In Surface Mount, you'll find this switch device. Multiplexers and demultiplexers have a number of circuits 1:1. Increasing operating temperature to around -40°C~125°C TA. The total number of terminations is 8. A electrical component with 1 channels is capable of high-quality output. It is safe to turn on and run the electronic component with a 5V voltage supply. This electronic part can be found in the 8 series. A SPST - NC switching circuit is used to build these analog multiplexers. Try searching with ADG1402 if you're looking for variants. Internally, this switch multiplexer has a resistance of 1.3Ohm. For functions related to 8 pins, please refer to the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. It is normally recommended that users do not supply the multiplexer with voltages higher than 16.5V. An effective Dual, Single supply digital multiplexer. There should be 5V voltage fed to the electrical part below 5V. The analogue multiplexer may be damaged if voltage is greater than 95μA. If put voltage greater than 16.5V on the multiplexer, damage may be caused to the device. The voltage should be at least 4.5V if you are using dual power supplies. The electrical part can be operated at 12V voltage levels. In order to operate the 1 inputs, there are several steps to follow. It is possible to transfer data over a 120MHz-bandwidth.
ADG1402BCPZ-REEL7 Features
1 Channels
Switch Circuit: SPST - NC
Bandwidth: 120MHz
ADG1402BCPZ-REEL7 Applications
There are a lot of Analog Devices Inc. ADG1402BCPZ-REEL7 Analog Switches & Multiplexers ICs applications.
- SONET
- Fiber In The Loop (FITL)
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Sample hold systems
- Digital Cross-Connects
- Channel Banks
- ISDN NT1/TA
- Optical Applications
- ATM
- Microprocessor controlled systems