ADG1408SRU-EP-RL7
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Digi-Reel® |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 4.7Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 4.9mW |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 225 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG1408 |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 12V |
| Number of Channels | 8 |
| Interface | Parallel |
| Number of Circuits | 1 |
| Max Supply Voltage | 16.5V |
| Min Supply Voltage | 5V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Power Dissipation | 4.9mW |
| Voltage - Supply, Single/Dual (±) | 5V~16.5V ±4.5V~16.5V |
| Bandwidth | 60MHz |
| Supply Current-Max (Isup) | 0.42mA |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 100 ns |
| Max Dual Supply Voltage | 16.5V |
| On-State Resistance (Max) | 4.7Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 200pA |
| Channel Capacitance (CS(off), CD(off)) | 14pF 80pF |
| On-state Resistance Match-Nom | 0.3Ohm |
| Switch Time (Ton, Toff) (Max) | 120ns, 120ns |
| Charge Injection | -15pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -70dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 440ns |
| Switch-off Time-Max | 370ns |
| Length | 5mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG1408SRU-EP-RL7 Overview
Shipping overseas is convenient with the electronic component packed in 16-TSSOP (0.173, 4.40mm Width). High reliability is provided by advanced packaging method Digi-Reel?. There is an analog multiplexer mounted in position Surface Mount. 8:1 is the ratio of multiplexer to demultiplexer circuits. The operating temperature is extended to around -55°C~125°C TA. In total, there have been 16 terminations. This electronic part offers high-quality output due to its 8 channels. A 5V voltage supply should turn on and run the electronic component. 16 pins are injected to the electronic part body. There are 1 circuits in this multiplexer. Search with ADG1408 if you are looking for analog multiplexer variants. It has an internal resistance of 4.7Ohm. For functions related to 16 pins, please refer to the datasheets. In this analog multiplexer, the value is Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 16.5V. 5V should be the lowest voltage fed to the electronic component. There is no problem with using dual supply voltage, but it should not exceed 16.5V. A dual power supply should have at least 4.5V voltage attached. There is an integrated analog IC SINGLE-ENDED MULTIPLEXER in the module. 12V operating voltages can be used with this electrical part. It is possible to transfer data over a 60MHz-bandwidth.
ADG1408SRU-EP-RL7 Features
8 Channels
Bandwidth: 60MHz
ADG1408SRU-EP-RL7 Applications
There are a lot of Analog Devices Inc. ADG1408SRU-EP-RL7 Analog Switches & Multiplexers ICs applications.
- FTTH
- Imaging
- Voice over IP/DSL – Integrated Access Devices, Smart
- Fiber to the Home
- Signal routing between systems
- Communication systems
- PCMCIA cards
- T1/E1 Terminals
- Frame Relay Equipment
- High speed data transmission line cards
