ADG1409SRU-EP
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 4.7Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 4.9mW |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 225 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | ADG1409 |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 12V |
| Number of Channels | 4 |
| Interface | Parallel |
| Number of Circuits | 2 |
| Max Supply Voltage | 16.5V |
| Min Supply Voltage | 5V |
| Analog IC - Other Type | DIFFERENTIAL MULTIPLEXER |
| Power Dissipation | 4.9mW |
| Number of Inputs | 8 |
| Voltage - Supply, Single/Dual (±) | 5V~16.5V ±4.5V~16.5V |
| Bandwidth | 115MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 100 ns |
| Max Dual Supply Voltage | 16.5V |
| On-State Resistance (Max) | 4.7Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 200pA |
| Channel Capacitance (CS(off), CD(off)) | 14pF 40pF |
| On-state Resistance Match-Nom | 0.3Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 120ns, 120ns |
| Charge Injection | -50pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -70dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 370ns |
| Length | 5mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG1409SRU-EP Overview
Shipping overseas is convenient with the electronic component packed in 16-TSSOP (0.173, 4.40mm Width). High reliability is provided by advanced packaging method Tube. In Surface Mount, this analog switch is mounted. Multiplexers and demultiplexers have a ratio of 4:1. Operating temperature around -55°C~125°C TA extended. In total, 16 terminations have occurred. Due to its 4 channels, the electrical component produces high-quality output. When a voltage supply of 5V is used, the electronic component should be turned on and run. It is injected into the electrical part body with 16 pins. Multiplexers built on a SP4T switching circuit are built. The circuits in this analogue multiplexer number 2. Try searching with ADG1409 if you're looking for variants. In this multiplexer, the internal resistance is 4.7Ohm. To find out what the 16 pins do, please refer to the datasheets. In this analog multiplexer, the value is Multiplexer or Switches. normally, users should not supply switches with voltages higher than 16.5V. 5V is the lowest voltage that should be fed to the electronic electronic part. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 16.5V. If you are using dual power supplies, you should attach at least 4.5V. There is an analog IC DIFFERENTIAL MULTIPLEXER integrated with this board. Operating voltages range from 12V. It is possible to operate 8 inputs. A 115MHz-bandwidth can be used for data transfer.
ADG1409SRU-EP Features
4 Channels
Switch Circuit: SP4T
Bandwidth: 115MHz
ADG1409SRU-EP Applications
There are a lot of Analog Devices Inc. ADG1409SRU-EP Analog Switches & Multiplexers ICs applications.
- SDH/SONET multiplexers
- Industrial control systems
- Precision instrumentation
- Precision data acquisition
- Cable Modem
- Relay Replacement
- Routers
- E1 Multiplexer
- Digital access cross connects
- Fiber to the Home
