ADG1412YRUZ-REEL7
| Parameters | |
|---|---|
| Normal Position | NO |
| Height Seated (Max) | 1.2mm |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 week ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 1.8Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 4.97mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG1412 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 12V |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Interface | Parallel |
| Max Supply Voltage | 16.5V |
| Min Supply Voltage | 5V |
| Test Frequency | 1MHz |
| Operating Supply Current | 220μA |
| Power Dissipation | 4.97mW |
| Max Supply Current | 380μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 150 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 5V~16.5V ±4.5V~16.5V |
| Supply Type | Dual, Single |
| Bandwidth | 170MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 120 ns |
| Max Dual Supply Voltage | 16.5V |
| On-State Resistance (Max) | 1.8Ohm |
| Min Dual Supply Voltage | 4.5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 80 dB |
| Current - Leakage (IS(off)) (Max) | 550pA |
| Channel Capacitance (CS(off), CD(off)) | 23pF 23pF |
| On-state Resistance Match-Nom | 0.13Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 150ns, 120ns |
| Insertion Loss (dB) | -0.35 dB |
| Charge Injection | -20pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -100dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 510ns |
| Switch-off Time-Max | 380ns |
ADG1412YRUZ-REEL7 Overview
Shipping overseas is convenient with the electronic component packed in 16-TSSOP (0.173, 4.40mm Width). Advanced packaging method Tape & Reel (TR) is used to provide high reliability. Surface Mount is where this multiplexer is located. Multiplexer and demultiplexer circuits have a number 1:1. Temperatures around -40°C~125°C TA are extended for operation. In total, there have been 16 terminations. The electronic part provides high-quality output because it has 1 channels. When the electronic component is given a voltage of 5V, it should be turned on and run. A total of 16 pins are injected into the body of the electronic part. Circuits based on SPST - NO switching are used to construct these analog switch ics. Try searching for the analog switch ic with ADG1412 if you are looking for variants. An switch multiplexer with 1.8Ohm internal resistance has a value of 1.8Ohm. Please refer to the datasheets for 16 pins functions. A analogue multiplexer of this type is a Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 16.5V to the switch device in normal circumstances. Analogue multiplexers of the Dual, Single supply type that are cost-effective. It is recommended to use 5V as the lowest voltage for the electrical part. 220μA current would be enough for this multiplexer to operate. The analogue multiplexer may be damaged if voltage is greater than 380μA. If put voltage greater than 16.5V on the multiplexer, damage may be caused to the device. If you are using a dual power supply, you should attach at least 4.5V. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. Operating voltages of 12V are compatible with the electrical part. It is possible to operate 4 inputs. A 170MHz-bandwidth can be used for data transfer.
ADG1412YRUZ-REEL7 Features
1 Channels
Switch Circuit: SPST - NO
220μA Supply Current
Bandwidth: 170MHz
ADG1412YRUZ-REEL7 Applications
There are a lot of Analog Devices Inc. ADG1412YRUZ-REEL7 Analog Switches & Multiplexers ICs applications.
- Battery Powered Systems
- Industrial control systems
- Data switching
- Wireless Local Loop
- E1 Multiplexer
- Mechanical reed relay replacement
- Channelized and Unchannelized DS3 applications
- Low-Voltage
- ISDN NT1/TA
- Microprocessor controlled systems
