ADG1421BCPZ-REEL7

145ns, 145ns SPST - NO 2.4Ohm Analog Switches BREAK-BEFORE-MAKE ADG1421 10 Pins 500pA 5V 10-VFDFN Exposed Pad, CSP

Manufacturer: Analog Devices Inc.
Nocochips NO: 84-ADG1421BCPZ-REEL7
Package: 10-VFDFN Exposed Pad, CSP
Datasheet: PDF
Stock: 692
Description: 145ns, 145ns SPST - NO 2.4Ohm Analog Switches BREAK-BEFORE-MAKE ADG1421 10 Pins 500pA 5V 10-VFDFN Exposed Pad, CSP(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Lifecycle Status	PRODUCTION (Last Updated: 1 week ago)
Contact Plating	Tin
Mounting Type	Surface Mount
Package / Case	10-VFDFN Exposed Pad, CSP
Surface Mount	YES
Number of Pins	10
Operating Temperature	-40°C~125°C TA
Packaging	Tape & Reel (TR)
JESD-609 Code	e3
Pbfree Code	no
Part Status	Active
Moisture Sensitivity Level (MSL)	3 (168 Hours)
Number of Terminations	10
ECCN Code	EAR99
Resistance	2.4Ohm
Subcategory	Multiplexer or Switches
Max Power Dissipation	1.8mW
Technology	CMOS
Terminal Form	NO LEAD
Peak Reflow Temperature (Cel)	260
Number of Functions	1
Supply Voltage	5V
Terminal Pitch	0.5mm
Time@Peak Reflow Temperature-Max (s)	30
Base Part Number	ADG1421
Pin Count	10
Qualification Status	Not Qualified
Operating Supply Voltage	12V
Polarity	Non-Inverting
Number of Channels	1
Interface	Parallel
Max Supply Voltage	16.5V
Min Supply Voltage	5V
Test Frequency	1MHz
Power Dissipation	1.8mW
Max Supply Current	190μA
Turn On Delay Time	145 ns
Number of Inputs	2
Voltage - Supply, Single/Dual (±)	5V~16.5V ±4.5V~16.5V
Supply Type	Dual, Single
Bandwidth	180MHz
Neg Supply Voltage-Nom (Vsup)	-5V
Turn-Off Delay Time	145 ns
Max Dual Supply Voltage	16.5V
On-State Resistance (Max)	2.4Ohm
Min Dual Supply Voltage	4.5V
Dual Supply Voltage	15V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	60 dB
Current - Leakage (IS(off)) (Max)	500pA
Channel Capacitance (CS(off), CD(off))	18pF 22pF
On-state Resistance Match-Nom	0.04Ohm
Switch Circuit	SPST - NO
Switch Time (Ton, Toff) (Max)	145ns, 145ns
Insertion Loss (dB)	0.12 dB
Charge Injection	-5pC
Channel-to-Channel Matching (ΔRon)	20m Ω
Crosstalk	-74dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Switch-off Time-Max	395ns
Normal Position	NO
Height Seated (Max)	0.8mm
Length	3mm
REACH SVHC	No SVHC
RoHS Status	ROHS3 Compliant
Lead Free	Contains Lead

ADG1421BCPZ-REEL7 Overview

Presented in 10-VFDFN Exposed Pad, CSP, this electrical component is convenient for overseas shipping. High reliability is achieved by using advanced packaging method Tape & Reel (TR). A switch device like this is mounted in Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. The operating temperature is extended to around -40°C~125°C TA. In total, 10 terminations have occurred. By its 1 channels, the electronic component provides high-quality output. An 5V voltage supply should allow the electrical part to be turned on and run. An injection of 10 pins is performed into the body of the electrical component. Circuits based on SPST - NO switching are used to construct these analog switch ics. Use ADG1421 to search for variants of the digital switches. It has an internal resistance of 2.4Ohm. Please refer to the datasheets for 10 pins functions. The analog multiplexer shown here is a typical Multiplexer or Switches. A voltage higher than 16.5V should not normally be supplied to the switches. A analog switch ic that has a cost-effective Dual, Single supply type. It is recommended that the electrical component receives a voltage of 5V. Putting voltage greater than 190μA on the multiplexer may cause damage. For this multiplexer, dual supply voltage is feasible, but it should not exceed 16.5V. When using dual power supplies, you should attach at least 4.5V. The electronic component can function from 12V. The electrical component supports 2 inputs. The data can be transferred over a wide range of bandwidths, called 180MHz bandwidths.