Parameters |
Pin Count |
16 |
Number of Outputs |
4 |
Qualification Status |
Not Qualified |
Operating Supply Voltage |
12V |
Number of Channels |
1 |
Interface |
Parallel |
Max Supply Voltage |
16.5V |
Min Supply Voltage |
5V |
Test Frequency |
100kHz |
Power Dissipation |
30μW |
Max Supply Current |
285μA |
Turn On Delay Time |
120 ns |
Number of Inputs |
2 |
Voltage - Supply, Single/Dual (±) |
5V~16.5V ±4.5V~16.5V |
Supply Type |
Dual, Single |
Bandwidth |
110MHz |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Turn-Off Delay Time |
130 ns |
Max Dual Supply Voltage |
16.5V |
On-State Resistance (Max) |
1.8Ohm |
Min Dual Supply Voltage |
4.5V |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
80 dB |
Current - Leakage (IS(off)) (Max) |
550pA |
Channel Capacitance (CS(off), CD(off)) |
23pF 50pF |
On-state Resistance Match-Nom |
0.13Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
120ns, 130ns |
Insertion Loss (dB) |
-0.18 dB |
Charge Injection |
-20pC |
Channel-to-Channel Matching (ΔRon) |
100m Ω |
Crosstalk |
-80dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Height Seated (Max) |
1mm |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 1 week ago) |
Mounting Type |
Surface Mount |
Package / Case |
16-VQFN Exposed Pad, CSP |
Surface Mount |
YES |
Number of Pins |
16 |
Operating Temperature |
-40°C~125°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e3 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
3 (168 Hours) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
1.8Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
30μW |
Technology |
CMOS |
Terminal Position |
QUAD |
Terminal Form |
NO LEAD |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
5V |
Terminal Pitch |
0.65mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
ADG1436 |
ADG1436YCPZ-REEL Overview
The electronic component is convenient to ship overseas because it is packed in a 16-VQFN Exposed Pad, CSP. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. There is an analog multiplexer mounted in position Surface Mount. In the multiplexer and demultiplexer, 2:1 represents the number of circuits. Operation at a temperature around -40°C~125°C TA. In total, 16 terminations have occurred. Due to its 1 channels, the electrical component produces high-quality output. If the voltage supply is 5V volts, the electrical component should be turned on and run. There is an electrical component included in the 16 series. Circuits based on SPDT switching are used to construct these analog switch ics. Use ADG1436 to search for variants of the digital switches. The internal resistance of this digital multiplexer is 1.8Ohm. Datasheets for 16 pin functions are available upon request. Theswitch device is a typical Multiplexer or Switches. Users should never supply a voltage higher than 16.5V to a switch device. The digital multiplexer has a low cost Dual, Single supply. It is recommended to use 5V as the lowest voltage for the electrical part. If put voltage greater than 285μA on the device, damage may be caused to the analogue multiplexer. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 16.5V. For dual power supplies, a voltage of at least 4.5V should be attached. The electrical part can be operated at 12V voltage levels. In order to operate the 2 inputs, there are several steps to follow. The transfer of data can be performed over 110MHz bandwidths. This digital multiplexer has 4 outputs.
ADG1436YCPZ-REEL Features
1 Channels
Switch Circuit: SPDT
Bandwidth: 110MHz
ADG1436YCPZ-REEL Applications
There are a lot of Analog Devices Inc. ADG1436YCPZ-REEL Analog Switches & Multiplexers ICs applications.
- Fiber In The Loop (FITL)
- Microprocessor controlled systems
- Sample-and-hold systems
- Transmit
- Multi-Line E1 Interface Cards
- Signal routing between systems
- Low-Voltage
- Microwave transmission systems
- E1 Network Equipment
- Cell phones