ADG1438BRUZ-REEL7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 weeks ago) |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 20 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Resistance | 11.5Ohm |
| Terminal Finish | MATTE TIN |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 225 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | ADG1438 |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 12V |
| Number of Channels | 8 |
| Interface | Serial |
| Number of Circuits | 1 |
| Max Supply Voltage | 16.5V |
| Min Supply Voltage | 5V |
| Analog IC - Other Type | SPDT |
| Operating Supply Current | 1nA |
| Power Dissipation | 30nW |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 5V~16.5V ±4.5V~16.5V |
| Supply Type | Dual, Single |
| Bandwidth | 82MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Max Dual Supply Voltage | 16.5V |
| On-State Resistance (Max) | 11.5Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 150pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 58pF |
| On-state Resistance Match-Nom | 0.6Ohm |
| Charge Injection | 4pC |
| Channel-to-Channel Matching (ΔRon) | 550m Ω |
| Crosstalk | -70dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 350ns |
| Switch-off Time-Max | 350ns |
| Signal Current-Max | 0.03A |
| Length | 6.5mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG1438BRUZ-REEL7 Overview
This electronic part is conveniently packaged in 20-TSSOP (0.173, 4.40mm Width), making it easy to ship abroad. High reliability is achieved by using advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. 8:1 is the ratio between multiplexers and demultiplexers. Operating temperature around -40°C~125°C TA extended. 20 terminations have been made so far. As a result of its 8 channels, this electronic component provides high-quality output. If the voltage supply is 5V volts, the electrical component should be turned on and run. An injection of 20 pins is performed into the body of the electrical component. There are 1 circuits in this multiplexer. ADG1438 can be used to search for analog multiplexer variants. An switch multiplexer with 11.5Ohm internal resistance has a value of 11.5Ohm. Datasheets for 20 pin functions are available upon request. A voltage higher than 16.5V should not normally be supplied to the switches. The digital multiplexer has a low cost Dual, Single supply. The lowest voltage fed to the electronic component should be 5V. It would be sufficient to run this analogue multiplexer with 1nA current. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 16.5V. A dual power supply should have at least 4.5V voltage attached. Integrated with SPDT analog IC. 12V operating voltages can be used with this electrical part. There are various bandwidths available for data transfer.
ADG1438BRUZ-REEL7 Features
8 Channels
1nA Supply Current
Bandwidth: 82MHz
ADG1438BRUZ-REEL7 Applications
There are a lot of Analog Devices Inc. ADG1438BRUZ-REEL7 Analog Switches & Multiplexers ICs applications.
- Microprocessor Controlled Analog Systems
- MP3 players
- PBXs
- Multiplexers
- Digital cross connects (DSX-1)
- SDH/SONET multiplexers
- DSUs
- Isolation
- High-Voltage
- Digital Cross-Connects
