ADG1604BRUZ

95ns, 173ns SP4T 1.1Ohm DUAL Analog Switches BREAK-BEFORE-MAKE ADG1604 14 Pins 200pA 5V 14-TSSOP (0.173, 4.40mm Width)

Manufacturer: Analog Devices Inc.
Nocochips NO: 84-ADG1604BRUZ
Package: 14-TSSOP (0.173, 4.40mm Width)
Datasheet: PDF
Stock: 739
Description: 95ns, 173ns SP4T 1.1Ohm DUAL Analog Switches BREAK-BEFORE-MAKE ADG1604 14 Pins 200pA 5V 14-TSSOP (0.173, 4.40mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Lifecycle Status	PRODUCTION (Last Updated: 2 weeks ago)
Contact Plating	Tin
Mounting Type	Surface Mount
Package / Case	14-TSSOP (0.173, 4.40mm Width)
Surface Mount	YES
Number of Pins	14
Operating Temperature	-40°C~125°C TA
Packaging	Tube
JESD-609 Code	e3
Pbfree Code	no
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	14
ECCN Code	EAR99
Resistance	1Ohm
Subcategory	Multiplexer or Switches
Max Power Dissipation	2.8mW
Technology	CMOS
Terminal Position	DUAL
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	1
Supply Voltage	5V
Terminal Pitch	0.65mm
Time@Peak Reflow Temperature-Max (s)	30
Base Part Number	ADG1604
Pin Count	14
Operating Supply Voltage	5V
Number of Channels	4
Interface	Parallel
Number of Circuits	1
Max Supply Voltage	16V
Min Supply Voltage	3.3V
Analog IC - Other Type	SINGLE-ENDED MULTIPLEXER
Nominal Supply Current	230μA
Power Dissipation	2.8mW
Number of Inputs	4
Voltage - Supply, Single/Dual (±)	3.3V~16V ±3.3V~8V
Bandwidth	19MHz
Supply Current-Max (Isup)	0.36mA
Neg Supply Voltage-Nom (Vsup)	-5V
Turn-Off Delay Time	95 ns
Max Dual Supply Voltage	8V
On-State Resistance (Max)	1.1Ohm
Min Dual Supply Voltage	3.3V
Multiplexer/Demultiplexer Circuit	4:1
Off-state Isolation-Nom	70 dB
Current - Leakage (IS(off)) (Max)	200pA
Channel Capacitance (CS(off), CD(off))	60pF 270pF
On-state Resistance Match-Nom	0.04Ohm
Switch Circuit	SP4T
Switch Time (Ton, Toff) (Max)	95ns, 173ns
Charge Injection	125pC
Channel-to-Channel Matching (ΔRon)	30m Ω
Crosstalk	-70dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Drain to Source Resistance	1Ohm
Signal Current-Max	0.378A
Height	1.05mm
Length	5.1mm
Width	4.5mm
Radiation Hardening	No
REACH SVHC	No SVHC
RoHS Status	ROHS3 Compliant
Lead Free	Contains Lead

ADG1604BRUZ Overview

Packed in 14-TSSOP (0.173, 4.40mm Width), the electronic component is convenient for shipping overseas. This high-reliability packaging method uses advanced packaging methods Tube. Mounted in Surface Mount is this multiplexer. The ratio between the number of multiplexer and demultiplexer circuits is 4:1. The operating temperature is extended to around -40°C~125°C TA. In total, there are 14 terminations. Due to its 4 channels, the electrical component produces high-quality output. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. An electrical component of this type can be found in the 14 series. These analog multiplexers are built based on SP4T switching circuits. Circuits number 1 make up this analogue multiplexer. Search with ADG1604 if you are looking for analog multiplexer variants. There is 1Ohm internal resistance in this digital multiplexer. You can find the functions of the 14 pins in the datasheets. This switch device is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 16V. 3.3V is the lowest voltage that should be fed to the electronic electronic part. There is no problem with using dual supply voltage, but it should not exceed 8V. The voltage should be at least 3.3V if you are using dual power supplies. There is an analog IC SINGLE-ENDED MULTIPLEXER integrated with this board. It can operate from 5V operating voltages. It is possible to operate 4 inputs. 19MHz-bandwidths can be used to transfer data between multiplexers. Drain to Source resistance for this electronic component is 1Ohm.