Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 1 week ago) |
Mounting Type |
Surface Mount |
Package / Case |
16-VQFN Exposed Pad, CSP |
Surface Mount |
YES |
Number of Pins |
16 |
Operating Temperature |
-40°C~125°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e3 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
3 (168 Hours) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
1.1Ohm |
Terminal Finish |
MATTE TIN |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
5.8mW |
Technology |
CMOS |
Terminal Position |
QUAD |
Terminal Form |
NO LEAD |
Peak Reflow Temperature (Cel) |
NOT SPECIFIED |
Number of Functions |
4 |
Terminal Pitch |
0.635mm |
Time@Peak Reflow Temperature-Max (s) |
NOT SPECIFIED |
Base Part Number |
ADG1611 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Qualification Status |
Not Qualified |
Power Supplies |
3.3/12/+-5V |
Interface |
Parallel |
Max Supply Voltage |
16V |
Min Supply Voltage |
3.3V |
Test Frequency |
1MHz |
Operating Supply Current |
320μA |
Power Dissipation |
5.8mW |
Max Supply Current |
480μA |
Throw Configuration |
SPST |
Turn On Delay Time |
212 ns |
Number of Inputs |
4 |
Voltage - Supply, Single/Dual (±) |
3.3V~16V ±3.3V~8V |
Supply Type |
Dual, Single |
Bandwidth |
42MHz |
Turn-Off Delay Time |
137 ns |
Max Dual Supply Voltage |
8V |
-3db Bandwidth |
38MHz |
On-State Resistance (Max) |
1.1Ohm |
Min Dual Supply Voltage |
3.3V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Current - Leakage (IS(off)) (Max) |
300pA |
Channel Capacitance (CS(off), CD(off)) |
60pF 60pF |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
156ns, 87ns |
Charge Injection |
170pC |
Channel-to-Channel Matching (ΔRon) |
30m Ω |
Crosstalk |
-110dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Drain to Source Resistance |
1.1Ohm |
Normal Position |
NO |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
ADG1611BCPZ-REEL7 Overview
Due to its 16-VQFN Exposed Pad, CSP packaging, the electronic part is convenient for international shipping. High reliability is achieved by using advanced packaging method Tape & Reel (TR). This analog switch is mounted in Surface Mount. There is 1:1 ratio between the number of multiplexers and demultiplexers. Increasing operating temperature to around -40°C~125°C TA. In total, there are 16 terminations. It is part of the design of the 16 series that this electronic component is included. Unlike digital switches, these are based on SPST - NC switching circuits. Try searching for ADG1611 variants of the analog switch ic. The internal resistance of this digital multiplexer is 1.1Ohm. The functions of 16 pins can be found in the datasheets. It is a typical Multiplexer or Switches analog multiplexer. In normalcircumstances, users should not exceed 16V volts for the multiplexer. The analog switch ic is of the Dual, Single supply type and is cost-effective. It is recommended that the electrical component receives a voltage of 3.3V. An operating current of 320μA would be sufficient for this switch device. If you put voltage higher than 480μA on the digital multiplexer, damage may occur. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 8V. For dual power supplies, a voltage of at least 3.3V should be attached. This analog switch ic utilizes SEPARATE OUTPUT output. It is possible to operate 4 inputs. In 42MHz-bandwidths, data can be transferred. Drain to Source resistance for this electronic component is 1.1Ohm.
ADG1611BCPZ-REEL7 Features
Switch Circuit: SPST - NC
320μA Supply Current
-3db Bandwidth: 38MHz
Bandwidth: 42MHz
Drain-to-Source resistance: 1.1Ohm
ADG1611BCPZ-REEL7 Applications
There are a lot of Analog Devices Inc. ADG1611BCPZ-REEL7 Analog Switches & Multiplexers ICs applications.
- Battery Powered Systems
- Cross Connects
- High-Voltage
- SDH/SONET multiplexers
- Audio and video signal routing
- Relay replacements
- Precision instrumentation
- T1/E1 Terminals
- Power routing
- Audio/video switches