ADG1613BCPZ-REEL7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 weeks ago) |
| Mounting Type | Surface Mount |
| Package / Case | 16-VQFN Exposed Pad, CSP |
| Number of Pins | 16 |
| Supplier Device Package | 16-LFCSP-VQ (4x4) |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Resistance | 1.1Ohm |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -40°C |
| Max Power Dissipation | 5.8mW |
| Base Part Number | ADG1613 |
| Number of Outputs | 4 |
| Number of Channels | 4 |
| Interface | Parallel |
| Number of Circuits | 4 |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 3.3V |
| Test Frequency | 1MHz |
| Power Dissipation | 5.8mW |
| Max Supply Current | 480μA |
| Turn On Delay Time | 212 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 3.3V~16V ±3.3V~8V |
| Supply Type | Dual, Single |
| Bandwidth | 38MHz |
| Turn-Off Delay Time | 137 ns |
| Max Dual Supply Voltage | 8V |
| -3db Bandwidth | 38MHz |
| On-State Resistance (Max) | 1.1Ohm |
| Min Dual Supply Voltage | 3.3V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 300pA |
| Channel Capacitance (CS(off), CD(off)) | 60pF 60pF |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 156ns, 87ns |
| Charge Injection | 170pC |
| Channel-to-Channel Matching (ΔRon) | 30mOhm |
| Crosstalk | -110dB @ 1MHz |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG1613BCPZ-REEL7 Overview
Shipping overseas is convenient due to the electrical component's packing in 16-VQFN Exposed Pad, CSP. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). It is mounted in the position Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. Around -40°C~125°C TA is the extended operating temperature. By its 4 channels, the electronic component provides high-quality output. A SPST - NO/NC switching circuit is used to build these analog multiplexers. The multiplexer consists of 4 circuits. Try searching with ADG1613 to find analog multiplexer variants. There is 1.1Ohm internal resistance in this digital multiplexer. To find out what the functions of 16 pins are, please refer to their datasheets. An abnormal situation would be for the switch device to be supplied with a voltage greater than 16V. The digital multiplexer has a low cost Dual, Single supply. 3.3V is the lowest voltage that should be fed to the electronic electronic part. It may damage the digital multiplexer if the voltage is higher than 480μA. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 8V. A dual power supply should have at least 3.3V voltage attached. The 4 inputs need to be operated in order to work. There are various bandwidths available for data transfer. The switches should not operate in an environment where the temperature is higher than 125°C. 4 outputs are included in the analogue multiplexer. Suppliers offer 16-LFCSP-VQ (4x4) packages.
ADG1613BCPZ-REEL7 Features
4 Channels
Switch Circuit: SPST - NO/NC
-3db Bandwidth: 38MHz
Bandwidth: 38MHz
ADG1613BCPZ-REEL7 Applications
There are a lot of Analog Devices Inc. ADG1613BCPZ-REEL7 Analog Switches & Multiplexers ICs applications.
- DVD-R
- Optical Applications
- Audio signal routing
- Channelized and Unchannelized DS3 applications
- Fault Tolerant Systems
- Voice over IP/DSL – Integrated Access Devices, Smart
- Cable PC
- PBX interfaces
- Microwave transmission systems
- Communications systems
