ADG1613BRUZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 weeks ago) |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 1.2Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5.8mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Terminal Pitch | 0.635mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG1613 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Interface | Parallel |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 3.3V |
| Test Frequency | 1MHz |
| Power Dissipation | 5.8mW |
| Max Supply Current | 480μA |
| Turn On Delay Time | 212 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 3.3V~16V ±3.3V~8V |
| Supply Type | Dual, Single |
| Bandwidth | 38MHz |
| Turn-Off Delay Time | 137 ns |
| Max Dual Supply Voltage | 8V |
| On-State Resistance (Max) | 1.1Ohm |
| Min Dual Supply Voltage | 3.3V |
| Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 300pA |
| Channel Capacitance (CS(off), CD(off)) | 60pF 60pF |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 156ns, 87ns |
| Charge Injection | 170pC |
| Channel-to-Channel Matching (ΔRon) | 30m Ω |
| Crosstalk | -110dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Height | 1.2mm |
| Length | 5.1mm |
| Width | 4.5mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG1613BRUZ Overview
Presented in 16-TSSOP (0.173, 4.40mm Width), this electrical component is convenient for overseas shipping. A high level of reliability can be achieved through the use of an advanced packaging method Tube. In Surface Mount, this analog switch is mounted. There is 1:1 ratio between the number of multiplexers and demultiplexers. The operating temperature is extended to around -40°C~125°C TA. The total number of terminations is 16. An injection of 16 pins is performed into the body of the electrical component. Circuits based on SPST - NO/NC switching are used to construct these analog switch ics. If you are looking for variants of the digital switch, trying search with ADG1613. There is 1.2Ohm internal resistance in this digital multiplexer. To find out what the 16 pins do, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 16V volts for the multiplexer. Dual, Single supply type digital switch with a low cost. The lowest voltage fed to the electronic component should be 3.3V. Put voltage above 480μA on the multiplexer to cause damage. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 8V. In the case of dual power supplies, you should connect at least 3.3V. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. Operating 4 inputs is required. 38MHz-bandwidths can be used to transfer data between multiplexers.
ADG1613BRUZ Features
Switch Circuit: SPST - NO/NC
Bandwidth: 38MHz
ADG1613BRUZ Applications
There are a lot of Analog Devices Inc. ADG1613BRUZ Analog Switches & Multiplexers ICs applications.
- Channel Banks
- T1/E1 Terminals
- Imaging
- Medical Instrumentation
- Battery Powered Systems
- E1 Multiplexer
- MP3 players
- Automotive applications
- Digital cross connects (DSX-1)
- Transmit
