ADG1613BRUZ-REEL7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 week ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 1.1Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5.8mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Terminal Pitch | 0.635mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG1613 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Polarity | Non-Inverting |
| Interface | Parallel |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 3.3V |
| Test Frequency | 1MHz |
| Operating Supply Current | 320μA |
| Power Dissipation | 5.8mW |
| Max Supply Current | 480μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 212 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 3.3V~16V ±3.3V~8V |
| Supply Type | Dual, Single |
| Bandwidth | 38MHz |
| Turn-Off Delay Time | 137 ns |
| Max Dual Supply Voltage | 8V |
| On-State Resistance (Max) | 1.1Ohm |
| Min Dual Supply Voltage | 3.3V |
| Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 300pA |
| Channel Capacitance (CS(off), CD(off)) | 60pF 60pF |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 156ns, 87ns |
| Charge Injection | 170pC |
| Channel-to-Channel Matching (ΔRon) | 30m Ω |
| Crosstalk | -110dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG1613BRUZ-REEL7 Overview
This electronic part is conveniently packaged in 16-TSSOP (0.173, 4.40mm Width), making it easy to ship abroad. High reliability is achieved by using advanced packaging method Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. An extended operating temperature of -40°C~125°C TA degrees Celsius. 16 terminations have been made so far. Into the electrical component body are injected 16 pins. SPST - NO/NC switching circuits are used in these analog switch ics. Try searching for ADG1613 variants of the analog switch ic. In this multiplexer, the internal resistance is 1.1Ohm. To find out what the 16 pins do, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 16V. The analog switch ic is of the Dual, Single supply type and is cost-effective. There should be 3.3V voltage fed to the electrical part below 3.3V. 320μA current would be enough for this multiplexer to operate. It may damage the digital multiplexer if the voltage is higher than 480μA. For this multiplexer, dual supply voltage is feasible, but it should not exceed 8V. The voltage should be at least 3.3V if you are using dual power supplies. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. There are 4 inputs to be operated. The transfer of data can be performed over 38MHz bandwidths.
ADG1613BRUZ-REEL7 Features
Switch Circuit: SPST - NO/NC
320μA Supply Current
Bandwidth: 38MHz
ADG1613BRUZ-REEL7 Applications
There are a lot of Analog Devices Inc. ADG1613BRUZ-REEL7 Analog Switches & Multiplexers ICs applications.
- SONET/SDH ADM
- Battery-powered systems
- Transmit
- Remote wireless modules
- Intelligent PBX
- Audio signal routing
- Channel Banks
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Sample hold systems
- Battery Powered Systems
