banner_page

ADG201AKN

300ns, 250ns SPST - NC 90Ohm Analog Switches BREAK-BEFORE-MAKE ADG201 16 Pins 2nA 15V 16-DIP (0.300, 7.62mm)


  • Manufacturer: Analog Devices Inc.
  • Nocochips NO: 84-ADG201AKN
  • Package: 16-DIP (0.300, 7.62mm)
  • Datasheet: PDF
  • Stock: 591
  • Description: 300ns, 250ns SPST - NC 90Ohm Analog Switches BREAK-BEFORE-MAKE ADG201 16 Pins 2nA 15V 16-DIP (0.300, 7.62mm)(Kg)

Details

Tags

Parameters
Mounting Type Through Hole
Package / Case 16-DIP (0.300, 7.62mm)
Surface Mount NO
Number of Pins 16
Operating Temperature -40°C~85°C TA
Packaging Tube
JESD-609 Code e0
Pbfree Code no
Part Status Obsolete
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 16
ECCN Code EAR99
Resistance 90Ohm
Terminal Finish Tin/Lead (Sn85Pb15)
Subcategory Multiplexer or Switches
Max Power Dissipation 33mW
Technology CMOS
Number of Functions 1
Supply Voltage 15V
Base Part Number ADG201
Pin Count 16
Operating Supply Voltage 15V
Polarity Inverting
Number of Channels 4
Interface Parallel
Max Supply Voltage 25V
Power Dissipation 33mW
Max Supply Current 2mA
Throw Configuration SPST
Turn On Delay Time 300 ns
Voltage - Supply, Single/Dual (±) 10V~15V ±10V~15V
Supply Type Dual
Neg Supply Voltage-Nom (Vsup) -15V
Turn-Off Delay Time 250 ns
Max Dual Supply Voltage 22V
On-State Resistance (Max) 90Ohm
High Level Output Current 30mA
Dual Supply Voltage 15V
Multiplexer/Demultiplexer Circuit 1:1
Off-state Isolation-Nom 80 dB
Current - Leakage (IS(off)) (Max) 2nA
Channel Capacitance (CS(off), CD(off)) 5pF
On-state Resistance Match-Nom 5Ohm
Switch Circuit SPST - NC
Switch Time (Ton, Toff) (Max) 300ns, 250ns
Charge Injection 20pC
Channel-to-Channel Matching (ΔRon) 4.5 Ω
Crosstalk -80dB @ 100kHz
Switching BREAK-BEFORE-MAKE
Normal Position NC
Height 3.3mm
Length 20.07mm
Width 6.35mm
Radiation Hardening No
RoHS Status Non-RoHS Compliant
Lead Free Contains Lead

ADG201AKN Overview


Shipping overseas is convenient with the electronic component packed in 16-DIP (0.300, 7.62mm). High reliability is achieved by using advanced packaging method Tube. Through Hole is where this multiplexer is located. Multiplexers and demultiplexers have a ratio of 1:1. The operating temperature is extended to around -40°C~85°C TA. The total number of terminations is 16. A high-quality output is provided by the electrical component's 4 channels. When a voltage supply of 15V is used, the electronic component should be turned on and run. As part of the design of the 16 series, this electronic part has been incorporated into the system. The analog switch ics are built using SPST - NC switching circuits. Using the ADG201 search parameter, you can discover variants of the switch. The internal resistance of this digital multiplexer is 90Ohm. The datasheets for the 16 pins explain the functions. The analog multiplexer shown here is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 25V. A cost-effective Dual supply type analogue multiplexer. Put voltage above 2mA on the multiplexer to cause damage. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 22V. A voltage of 15V can be used to operate the electronic component.

ADG201AKN Features


4 Channels
Switch Circuit: SPST - NC

ADG201AKN Applications


There are a lot of Analog Devices Inc. ADG201AKN Analog Switches & Multiplexers ICs applications.

  • Audio and video signal routing
  • ATM
  • Imaging
  • Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
  • Precision instrumentation
  • Fiber In The Loop (FITL)
  • Switching Systems
  • Transmit
  • High speed data transmission line cards
  • Cable Telephony – NIU, Set-Top Box, Home Side Box

Write a review

Note: HTML is not translated!
    Bad           Good