Parameters |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Surface Mount |
YES |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
90Ohm |
Terminal Finish |
Tin/Lead (Sn85Pb15) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
33mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
235 |
Number of Functions |
1 |
Supply Voltage |
15V |
Terminal Pitch |
1.27mm |
Time@Peak Reflow Temperature-Max (s) |
20 |
Base Part Number |
ADG201 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Operating Supply Voltage |
15V |
Number of Channels |
4 |
Interface |
Parallel |
Max Supply Voltage |
25V |
Power Dissipation |
33mW |
Max Supply Current |
2mA |
Throw Configuration |
SPST |
Turn On Delay Time |
300 ns |
Voltage - Supply, Single/Dual (±) |
10V~15V ±10V~15V |
Supply Type |
Dual |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
250 ns |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
90Ohm |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
80 dB |
Current - Leakage (IS(off)) (Max) |
2nA |
Channel Capacitance (CS(off), CD(off)) |
5pF |
On-state Resistance Match-Nom |
5Ohm |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
300ns, 250ns |
Charge Injection |
20pC |
Channel-to-Channel Matching (ΔRon) |
4.5 Ω |
Crosstalk |
-80dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Normal Position |
NC |
Height Seated (Max) |
1.75mm |
Length |
9.9mm |
Width |
3.9mm |
Radiation Hardening |
No |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
ADG201AKR Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-SOIC (0.154, 3.90mm Width). Advanced packaging method Tube is used to provide high reliability. It is mounted in the position Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. Operating temperature extended to -40°C~85°C TA. 16 terminations have been made so far. Due to its 4 channels, the electrical component produces high-quality output. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. It is part of the design of the 16 series that this electronic component is included. A SPST - NC switching circuit is used to build these analog multiplexers. ADG201 can be used to search for analog multiplexer variants. A 90Ohm internal resistance characterizes this multiplexer. Please refer to the datasheets for 16 pins functions. Theswitch device is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 25V. A analog switch ic that has a cost-effective Dual supply type. If put voltage greater than 2mA on the device, damage may be caused to the analogue multiplexer. For this multiplexer, dual supply voltage is feasible, but it should not exceed 22V. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. It can operate from 15V operating voltages.
ADG201AKR Features
4 Channels
Switch Circuit: SPST - NC
ADG201AKR Applications
There are a lot of Analog Devices Inc. ADG201AKR Analog Switches & Multiplexers ICs applications.
- DSUs
- Microwave transmission systems
- Power routing
- Precision data acquisition
- Industrial and process control systems
- T1/E1 Terminals
- Avionics test equipment
- Fault Tolerant Systems
- High reliability control systems
- Automatic test equipment