ADG201AKR-REEL
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 90Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 33mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG201 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 15V |
| Number of Channels | 4 |
| Interface | Parallel |
| Max Supply Voltage | 25V |
| Operating Supply Current | 600μA |
| Power Dissipation | 33mW |
| Max Supply Current | 2mA |
| Throw Configuration | SPST |
| Turn On Delay Time | 300 ns |
| Voltage - Supply, Single/Dual (±) | 10V~15V ±10V~15V |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 90Ohm |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 80 dB |
| Current - Leakage (IS(off)) (Max) | 2nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 300ns, 250ns |
| Charge Injection | 20pC |
| Channel-to-Channel Matching (ΔRon) | 4.5 Ω |
| Crosstalk | -80dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG201AKR-REEL Overview
This electronic part is conveniently packaged in 16-SOIC (0.154, 3.90mm Width), making it easy to ship abroad. High reliability is ensured by the advanced packaging method Tape & Reel (TR). This analog switch is mounted in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Operating temperature extended to -40°C~85°C TA. There are 16 terminations totally. A high-quality output is provided by the electrical component's 4 channels. A 15V voltage supply should turn on and run the electronic component. It is part of the design of the 16 series that this electronic component is included. The analog switch ics are built using SPST - NC switching circuits. Try searching for ADG201 variants of the analog switch ic. There is 90Ohm internal resistance in this digital multiplexer. You can find the functions of the 16 pins in the datasheets. Theswitch device is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 25V to the switch device in normal circumstances. Analog switch ics with Dual supply type are cost-effective. The switch device would be able to operate with 600μA current. When the digital multiplexer is charged above 2mA, damage can occur. There is no problem with using dual supply voltage, but it should not exceed 22V. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. There is a voltage range of 15V operating voltages for the electrical part.
ADG201AKR-REEL Features
4 Channels
Switch Circuit: SPST - NC
600μA Supply Current
ADG201AKR-REEL Applications
There are a lot of Analog Devices Inc. ADG201AKR-REEL Analog Switches & Multiplexers ICs applications.
- High reliability control systems
- Access Concentrators
- Multi-Line E1 Interface Cards
- Battery-powered systems
- Central office
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- HDTV
- Intelligent PBX
- Microprocessor controlled systems
- MP3 players
