ADG201AKRZ-REEL7
| Parameters | |
|---|---|
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 33mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG201 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 15V |
| Number of Channels | 4 |
| Interface | Parallel |
| Max Supply Voltage | 25V |
| Operating Supply Current | 600μA |
| Power Dissipation | 33mW |
| Max Supply Current | 2mA |
| Throw Configuration | SPST |
| Turn On Delay Time | 300 ns |
| Voltage - Supply, Single/Dual (±) | 10V~15V ±10V~15V |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 90Ohm |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 80 dB |
| Current - Leakage (IS(off)) (Max) | 2nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 300ns, 250ns |
| Charge Injection | 20pC |
| Channel-to-Channel Matching (ΔRon) | 4.5 Ω |
| Crosstalk | -80dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 months ago) |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 90Ohm |
| Terminal Finish | Matte Tin (Sn) |
ADG201AKRZ-REEL7 Overview
Packed in 16-SOIC (0.154, 3.90mm Width), the electronic component is convenient for shipping overseas. High reliability is achieved by using advanced packaging method Tape & Reel (TR). It is mounted in the position Surface Mount. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. An extended operating temperature of -40°C~85°C TA degrees Celsius. 16 terminations have been made so far. A 4 channel electronic part produces high-quality output. If the voltage supply is 15V volts, the electrical component should be turned on and run. The electrical component body receives 16 pins. On the other hand, analog switches can be constructed using SPST - NC switching circuits. If you are looking for variants of the digital switch, trying search with ADG201. A 90Ohm internal resistance characterizes this multiplexer. The datasheets for the 16 pins explain the functions. Multiplexer or Switches is a typical switch device. Multiplexers should not be powered above 25V in normal situations. Dual supply type digital switch with a low cost. This digital switch can be operated with a current of 600μA. Putting voltage greater than 2mA on the multiplexer may cause damage. For this switch, a dual supply voltage is feasible, but it must not exceed 22VAs far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. Operating voltages range from 15V.
ADG201AKRZ-REEL7 Features
4 Channels
Switch Circuit: SPST - NC
600μA Supply Current
ADG201AKRZ-REEL7 Applications
There are a lot of Analog Devices Inc. ADG201AKRZ-REEL7 Analog Switches & Multiplexers ICs applications.
- Communications systems
- Multi-Line E1 Interface Cards
- SONET/SDH ADM
- Medical systems
- Signal routing between systems
- Cell phones
- Digital access cross connects
- PBXs
- Microprocessor Controlled Analog Systems
- Cable Telephony – NIU, Set-Top Box, Home Side Box
