Parameters |
Contact Plating |
Lead, Tin |
Mount |
Through Hole |
Mounting Type |
Through Hole |
Package / Case |
16-DIP (0.300, 7.62mm) |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
50Ohm |
Terminal Finish |
Tin/Lead (Sn85Pb15) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
240mW |
Technology |
CMOS |
Peak Reflow Temperature (Cel) |
NOT APPLICABLE |
Number of Functions |
4 |
Supply Voltage |
15V |
Reach Compliance Code |
not_compliant |
Time@Peak Reflow Temperature-Max (s) |
NOT APPLICABLE |
Base Part Number |
ADG201 |
Pin Count |
16 |
Qualification Status |
Not Qualified |
Polarity |
Non-Inverting |
Number of Channels |
4 |
Interface |
Parallel |
Max Supply Voltage |
16.5V |
Min Supply Voltage |
10.8V |
Power Dissipation |
240mW |
Max Supply Current |
10mA |
Throw Configuration |
SPST |
Turn On Delay Time |
50 ns |
Voltage - Supply, Single/Dual (±) |
10.8V~16.5V ±13.5V~16.5V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
50 ns |
Max Dual Supply Voltage |
16.5V |
On-State Resistance (Max) |
50Ohm |
Min Dual Supply Voltage |
10.8V |
High Level Output Current |
20mA |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
72 dB |
Current - Leakage (IS(off)) (Max) |
1nA |
Channel Capacitance (CS(off), CD(off)) |
10pF 10pF |
On-state Resistance Match-Nom |
3Ohm |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
75ns, 75ns |
Charge Injection |
10pC |
Channel-to-Channel Matching (ΔRon) |
1.5 Ω |
Crosstalk |
-86dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
75ns |
Switch-off Time-Max |
75ns |
Normal Position |
NC |
Length |
19.055mm |
Width |
7.62mm |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
ADG201HSJN Overview
Packed in 16-DIP (0.300, 7.62mm), the electronic component is convenient for shipping overseas. In order to provide high reliability, an advanced packaging method Tube is used. The multiplexer is located in Through Hole. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Operating temperature around -40°C~85°C TA extended. Total terminations are 16. This electronic part offers high-quality output due to its 4 channels. An 15V voltage supply should allow the electrical part to be turned on and run. As part of the design of the 16 series, this electronic part has been incorporated into the system. These analog multiplexers are built based on SPST - NC switching circuits. ADG201 can be used to search for analog multiplexer variants. Analog switches have 50Ohm internal resistance. To find out what the functions of 16 pins are, please refer to their datasheets. It is a typical Multiplexer or Switches analog multiplexer. Multiplexers should not be powered above 16.5V in normal situations. The analog switch ic is of the Dual, Single supply type and is cost-effective. In order for the electronic part to function properly, the lowest voltage should be 10.8V. The switch multiplexer may be damaged if it is exposed to voltage greater than 10mA. For this multiplexer, dual supply voltage is feasible, but it should not exceed 16.5V. If you are using a dual power supply, you should attach at least 10.8V.
ADG201HSJN Features
4 Channels
Switch Circuit: SPST - NC
ADG201HSJN Applications
There are a lot of Analog Devices Inc. ADG201HSJN Analog Switches & Multiplexers ICs applications.
- High-Voltage
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- RGB switches
- Microprocessor controlled systems
- High speed data transmission line cards
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Routers
- Data switching
- SDH/SONET multiplexers
- Video switching