ADG201HSKR
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 50Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 240mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 235 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | ADG201 |
| Pin Count | 16 |
| Polarity | Inverting |
| Number of Channels | 4 |
| Interface | Parallel |
| Max Supply Voltage | 16.5V |
| Min Supply Voltage | 10.8V |
| Power Dissipation | 240mW |
| Max Supply Current | 10mA |
| Throw Configuration | SPST |
| Turn On Delay Time | 50 ns |
| Voltage - Supply, Single/Dual (±) | 10.8V~16.5V ±13.5V~16.5V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 50 ns |
| Max Dual Supply Voltage | 16.5V |
| On-State Resistance (Max) | 50Ohm |
| Min Dual Supply Voltage | 10.8V |
| High Level Output Current | 20mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 10pF 10pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 50ns, 50ns |
| Charge Injection | 10pC |
| Channel-to-Channel Matching (ΔRon) | 1.5 Ω |
| Crosstalk | -86dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Height | 1.5mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG201HSKR Overview
As the electronic part is packed in 16-SOIC (0.154, 3.90mm Width), international shipping is convenient. The advanced packaging method Tube provides high reliability. Surface Mount is where this multiplexer is located. 1:1 is the number of circuits in the multiplexer and demultiplexer. Operating temperature around -40°C~85°C TA extended. The total number of terminations is 16. A electrical component with 4 channels is capable of high-quality output. A 15V voltage supply should turn on and run the electronic component. This electrical component is included in the 16 series of products. A SPST - NC switching circuit is used to build these analog multiplexers. Try searching for ADG201 variants of the analog switch ic. A 50Ohm internal resistance characterizes this multiplexer. You can find the functions of the 16 pins in the datasheets. This switch device is a typical Multiplexer or Switches. Multiplexers should not be powered above 16.5V in normal situations. Analogue multiplexers of the Dual, Single supply type that are cost-effective. 10.8V is the lowest voltage the electrical component should receive. A digital multiplexer may suffer damage if voltage is applied above 10mA. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 16.5V. For dual power supplies, a voltage of at least 10.8V should be attached.
ADG201HSKR Features
4 Channels
Switch Circuit: SPST - NC
ADG201HSKR Applications
There are a lot of Analog Devices Inc. ADG201HSKR Analog Switches & Multiplexers ICs applications.
- Wireless Local Loop
- PBXs
- 65 V DACs
- Intelligent PBX
- High-Voltage
- Fiber In The Loop (FITL)
- ISDN NT1/TA
- Medical Instrumentation
- New designs requiring multiplexer functions
- Data switching
