banner_page

ADG202ABQ

300ns, 250ns SPST - NO 90Ohm DUAL Analog Switches BREAK-BEFORE-MAKE ADG202 16 Pins 2nA 15V 16-CDIP (0.300, 7.62mm)


  • Manufacturer: Analog Devices Inc.
  • Nocochips NO: 84-ADG202ABQ
  • Package: 16-CDIP (0.300, 7.62mm)
  • Datasheet: PDF
  • Stock: 494
  • Description: 300ns, 250ns SPST - NO 90Ohm DUAL Analog Switches BREAK-BEFORE-MAKE ADG202 16 Pins 2nA 15V 16-CDIP (0.300, 7.62mm)(Kg)

Details

Tags

Parameters
Mounting Type Through Hole
Package / Case 16-CDIP (0.300, 7.62mm)
Surface Mount NO
Number of Pins 16
Operating Temperature -40°C~85°C TA
Packaging Tube
JESD-609 Code e0
Part Status Obsolete
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 16
ECCN Code EAR99
Resistance 90Ohm
Terminal Finish Tin/Lead (Sn63Pb37)
Subcategory Multiplexer or Switches
Technology CMOS
Terminal Position DUAL
Peak Reflow Temperature (Cel) NOT SPECIFIED
Number of Functions 1
Supply Voltage 15V
Reach Compliance Code not_compliant
Time@Peak Reflow Temperature-Max (s) NOT SPECIFIED
Base Part Number ADG202
Output SEPARATE OUTPUT
Pin Count 16
Qualification Status Not Qualified
Power Supplies +-15V
Number of Channels 4
Max Supply Voltage 25V
Power Dissipation 470mW
Throw Configuration SPST
Voltage - Supply, Single/Dual (±) 10V~15V ±10V~15V
Neg Supply Voltage-Nom (Vsup) -15V
Max Dual Supply Voltage 22V
On-State Resistance (Max) 90Ohm
Multiplexer/Demultiplexer Circuit 1:1
Off-state Isolation-Nom 80 dB
Current - Leakage (IS(off)) (Max) 2nA
Channel Capacitance (CS(off), CD(off)) 5pF
On-state Resistance Match-Nom 5Ohm
Switch Circuit SPST - NO
Switch Time (Ton, Toff) (Max) 300ns, 250ns
Charge Injection 20pC
Channel-to-Channel Matching (ΔRon) 4.5 Ω
Crosstalk -80dB @ 100kHz
Switching BREAK-BEFORE-MAKE
Switch-on Time-Max 300ns
Switch-off Time-Max 250ns
Normal Position NO
Width 7.62mm
REACH SVHC Unknown
RoHS Status Non-RoHS Compliant

ADG202ABQ Overview


The electronic component is convenient to ship overseas because it is packed in a 16-CDIP (0.300, 7.62mm). To ensure high reliability, a new packaging method Tube is used. It is mounted in the position Through Hole. Multiplexers and demultiplexers have a number of circuits 1:1. Operating temperature around -40°C~85°C TA extended. In total, there have been 16 terminations. The electronic part provides high-quality output because it has 4 channels. If the voltage supply is 15V volts, the electrical component should be turned on and run. A total of 16 pins are injected into the electrical part body. Multiplexers built on a SPST - NO switching circuit are built. Try searching with ADG202 if you're looking for variants. An switch multiplexer with 90Ohm internal resistance has a value of 90Ohm. For details about the functions of 16 pins, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. A voltage higher than 25V should not normally be supplied to the switches. Despite this switch's dual supply capability, its voltage should not exceed 22V. In this switch multiplexer, there are SEPARATE OUTPUT outputs available.

ADG202ABQ Features


4 Channels
Switch Circuit: SPST - NO

ADG202ABQ Applications


There are a lot of Analog Devices Inc. ADG202ABQ Analog Switches & Multiplexers ICs applications.

  • E1 Network Equipment
  • Remote wireless modules
  • Precision data acquisition
  • Avionics test equipment
  • Automotive applications
  • Relay Replacement
  • Precision instrumentation
  • Switching Systems
  • Cell phones
  • PBX interfaces

Write a review

Note: HTML is not translated!
    Bad           Good