ADG211AKN
| Parameters | |
|---|---|
| Resistance | 115Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Base Part Number | ADG211 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 15V |
| Number of Channels | 4 |
| Max Supply Voltage | 25V |
| Power Dissipation | 22.5mW |
| Max Supply Current | 1mA |
| Throw Configuration | SPST |
| Turn On Delay Time | 600 ns |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 450 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 115Ohm |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 80 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| On-state Resistance Match-Nom | 5.8Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 600ns, 450ns |
| Charge Injection | 20pC |
| Channel-to-Channel Matching (ΔRon) | 5.75 Ω |
| Crosstalk | -80dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 115Ohm |
| Normal Position | NC |
| Voltage - Supply, Dual (V±) | ±15V |
| Length | 19.055mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
ADG211AKN Overview
This electronic part is conveniently packaged in 16-DIP (0.300, 7.62mm), making it easy to ship abroad. This packaging method provides high reliability because it uses advanced packaging techniques. It is mounted in the position Through Hole. Multiplexers and demultiplexers have the same number of circuits 1:1. Operational temperature extended around -40°C~85°C TA. 16 terminations have been made so far. The electronic part delivers high-quality output through its 4 channels. It is safe to turn on and run the electronic component with a 15V voltage supply. An injection of 16 pins is performed into the body of the electrical component. A SPST - NC switching circuit is used for these analog switches. Try searching for ADG211 variants of the analog switch ic. There is 115Ohm internal resistance in this digital multiplexer. The datasheets for the 16 pins explain the functions. It is a typical Multiplexer or Switches analog multiplexer. It is generally not recommended to supply a voltage higher than 25V to the switch device in normal circumstances. Analogue multiplexer with a Dual supply type that is cost-effective. Put voltage above 1mA on the multiplexer to cause damage. For this multiplexer, dual supply voltage is feasible, but it should not exceed 22V. There are SEPARATE OUTPUT outputs on this analog switch ic. 15V operating voltages can be used with this electrical part. Drain to Source resistance for this electronic component is 115Ohm.
ADG211AKN Features
4 Channels
Switch Circuit: SPST - NC
Drain-to-Source resistance: 115Ohm
ADG211AKN Applications
There are a lot of Analog Devices Inc. ADG211AKN Analog Switches & Multiplexers ICs applications.
- Intelligent PBX
- PBXs
- Isolation
- Channel Banks
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Battery Powered Instruments
- Precision test equipment
- Battery Powered Systems
- Cellular phones
- Avionics
