ADG211AKNZ
| Parameters | |
|---|---|
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Base Part Number | ADG211 |
| Pin Count | 16 |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Number of Channels | 4 |
| Interface | Parallel |
| Max Supply Voltage | 25V |
| Power Dissipation | 22.5mW |
| Max Supply Current | 1mA |
| Throw Configuration | SPST |
| Turn On Delay Time | 600 ns |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 450 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 115Ohm |
| High Level Output Current | 30mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 80 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| On-state Resistance Match-Nom | 5.8Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 600ns, 450ns |
| Charge Injection | 20pC |
| Channel-to-Channel Matching (ΔRon) | 5.75 Ω |
| Crosstalk | -80dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 115mOhm |
| Normal Position | NC |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 3.3mm |
| Length | 20.07mm |
| Width | 6.35mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 4 weeks ago) |
| Contact Plating | Tin |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 115Ohm |
ADG211AKNZ Overview
Shipping overseas is convenient with the electronic component packed in 16-DIP (0.300, 7.62mm). High reliability is achieved by using advanced packaging method Tube. In Through Hole, you'll find this switch device. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. An extended operating temperature of -40°C~85°C TA degrees Celsius. Total terminations are 16. By its 4 channels, the electronic component provides high-quality output. An 15V voltage supply should allow the electrical part to be turned on and run. A total of 16 pins are injected into the body of the electronic part. A SPST - NC switching circuit is used to build these analog multiplexers. Try searching for ADG211 variants of the analog switch ic. Analog switches have 115Ohm internal resistance. To find out what the functions of 16 pins are, please refer to their datasheets. Theswitch device is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 25V. Analog switch ics with Dual supply type are cost-effective. If put voltage greater than 1mA on the device, damage may be caused to the analogue multiplexer. For this multiplexer, dual supply voltage is feasible, but it should not exceed 22V. The electrical part can be operated at 5V voltage levels. There is 115mOhm Drain to Source resistance on this electronic part.
ADG211AKNZ Features
4 Channels
Switch Circuit: SPST - NC
Drain-to-Source resistance: 115mOhm
ADG211AKNZ Applications
There are a lot of Analog Devices Inc. ADG211AKNZ Analog Switches & Multiplexers ICs applications.
- Optical Applications
- Voice over IP/DSL – Integrated Access Devices, Smart
- Industrial and process control systems
- Cell phones
- E1 Multiplexer
- High-Voltage
- Industrial control systems
- Video switching
- Audio and video signal routing
- Channel Banks
