ADG211AKP
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 20-LCC (J-Lead) |
| Surface Mount | YES |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Resistance | 115Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | J BEND |
| Peak Reflow Temperature (Cel) | 225 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG211 |
| Output | SEPARATE OUTPUT |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 15V |
| Number of Channels | 4 |
| Max Supply Voltage | 25V |
| Power Dissipation | 470mW |
| Throw Configuration | SPST |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 115Ohm |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 80 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 600ns, 450ns |
| Charge Injection | 20pC |
| Channel-to-Channel Matching (ΔRon) | 5.75 Ω |
| Crosstalk | -80dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 600ns |
| Normal Position | NC |
| Voltage - Supply, Dual (V±) | ±15V |
| Length | 8.965mm |
| Width | 8.965mm |
| RoHS Status | Non-RoHS Compliant |
ADG211AKP Overview
Due to its 20-LCC (J-Lead) packaging, the electronic part is convenient for international shipping. A high level of reliability can be achieved through the use of an advanced packaging method Tube. Surface Mount is where this multiplexer is located. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Around -40°C~85°C TA is the extended operating temperature. There are 20 terminations totally. A electrical component with 4 channels is capable of high-quality output. When a voltage supply of 15V is used, the electronic component should be turned on and run. An electrical component of this type can be found in the 20 series. The analog switch ics are built using SPST - NC switching circuits. Try searching with ADG211 if you're looking for variants. The internal resistance of this digital multiplexer is 115Ohm. For functions related to 20 pins, please refer to the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. Multiplexers should not be powered above 25V in normal situations. Despite this switch's dual supply capability, its voltage should not exceed 22V. There are SEPARATE OUTPUT outputs on this analog switch ic. There is a voltage range of 15V operating voltages for the electrical part.
ADG211AKP Features
4 Channels
Switch Circuit: SPST - NC
ADG211AKP Applications
There are a lot of Analog Devices Inc. ADG211AKP Analog Switches & Multiplexers ICs applications.
- Battery Powered Systems
- Access Concentrators
- Precision data acquisition
- High reliability control systems
- MP3 players
- Mechanical reed relay replacement
- Central office
- SDH
- Communications systems
- Industrial control systems
