banner_page

ADG211AKR

600ns, 450ns SPST - NC 115Ohm Analog Switches BREAK-BEFORE-MAKE ADG211 16 Pins 5nA 15V 16-SOIC (0.154, 3.90mm Width)


  • Manufacturer: Analog Devices Inc.
  • Nocochips NO: 84-ADG211AKR
  • Package: 16-SOIC (0.154, 3.90mm Width)
  • Datasheet: PDF
  • Stock: 319
  • Description: 600ns, 450ns SPST - NC 115Ohm Analog Switches BREAK-BEFORE-MAKE ADG211 16 Pins 5nA 15V 16-SOIC (0.154, 3.90mm Width)(Kg)

Details

Tags

Parameters
Terminal Finish Tin/Lead (Sn85Pb15)
Subcategory Multiplexer or Switches
Max Power Dissipation 470mW
Technology CMOS
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 240
Number of Functions 4
Supply Voltage 15V
Terminal Pitch 1.27mm
Time@Peak Reflow Temperature-Max (s) 20
Base Part Number ADG211
Pin Count 16
Operating Supply Voltage 5V
Polarity Inverting, Non-Inverting
Number of Channels 4
Interface Parallel
Max Supply Voltage 25V
Nominal Supply Current 100μA
Power Dissipation 22.5mW
Max Supply Current 1mA
Throw Configuration SPST
Turn On Delay Time 600 ns
Supply Type Dual
Neg Supply Voltage-Nom (Vsup) -15V
Turn-Off Delay Time 450 ns
Max Dual Supply Voltage 22V
On-State Resistance (Max) 115Ohm
High Level Output Current 30mA
Dual Supply Voltage 15V
Multiplexer/Demultiplexer Circuit 1:1
Off-state Isolation-Nom 80 dB
Current - Leakage (IS(off)) (Max) 5nA
Channel Capacitance (CS(off), CD(off)) 5pF 5pF
Switch Circuit SPST - NC
Switch Time (Ton, Toff) (Max) 600ns, 450ns
Charge Injection 20pC
Channel-to-Channel Matching (ΔRon) 5.75 Ω
Crosstalk -80dB @ 100kHz
Switching BREAK-BEFORE-MAKE
Normal Position NC
Voltage - Supply, Dual (V±) ±15V
Height 1.5mm
Length 10mm
Width 4mm
Radiation Hardening No
RoHS Status Non-RoHS Compliant
Lead Free Contains Lead
Contact Plating Lead, Tin
Mounting Type Surface Mount
Package / Case 16-SOIC (0.154, 3.90mm Width)
Surface Mount YES
Number of Pins 16
Operating Temperature -40°C~85°C TA
Packaging Tube
JESD-609 Code e0
Pbfree Code no
Part Status Obsolete
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 16
ECCN Code EAR99
Resistance 115Ohm

ADG211AKR Overview


The electronic part can be shipped overseas conveniently because it is packaged in 16-SOIC (0.154, 3.90mm Width). The advanced packaging method Tube provides high reliability. This analog switch is mounted in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Operating temperature around -40°C~85°C TA extended. Total terminations are 16. A 4 channel electronic part produces high-quality output. If the voltage supply is 15V volts, the electrical component should be turned on and run. There are 16 pins injected into the electronic part body. The analog switch ics are built using SPST - NC switching circuits. Try searching for the analog switch ic with ADG211 if you are looking for variants. It has an internal resistance of 115Ohm. To find out what the 16 pins do, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. normally, users should not supply switches with voltages higher than 25V. Analog switch ics with Dual supply type are cost-effective. If you put voltage higher than 1mA on the digital multiplexer, damage may occur. Despite this switch device's dual supply capability, its voltage should not exceed 22V. 5V operating voltages can be used with this electrical part.

ADG211AKR Features


4 Channels
Switch Circuit: SPST - NC

ADG211AKR Applications


There are a lot of Analog Devices Inc. ADG211AKR Analog Switches & Multiplexers ICs applications.

  • Industrial and process control systems
  • Avionics
  • Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
  • Voice over IP/DSL – Integrated Access Devices, Smart
  • Switching Systems
  • PDH Multiplexers
  • PCMCIA cards
  • Low-Voltage
  • Industrial
  • SDH

Write a review

Note: HTML is not translated!
    Bad           Good