ADG211AKRZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 week ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 115Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG211 |
| Pin Count | 16 |
| Operating Supply Voltage | 5V |
| Polarity | Inverting, Non-Inverting |
| Number of Channels | 4 |
| Interface | Parallel |
| Max Supply Voltage | 25V |
| Power Dissipation | 22.5mW |
| Max Supply Current | 1mA |
| Throw Configuration | SPST |
| Turn On Delay Time | 600 ns |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 450 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 115Ohm |
| High Level Output Current | 30mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 80 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 600ns, 450ns |
| Charge Injection | 20pC |
| Channel-to-Channel Matching (ΔRon) | 5.75 Ω |
| Crosstalk | -80dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 1.5mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG211AKRZ Overview
Due to its 16-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. This packaging method provides high reliability because it uses advanced packaging techniques. There is an analog multiplexer mounted in position Surface Mount. 1:1 is the number of circuits in the multiplexer and demultiplexer. Operating temperature extended to -40°C~85°C TA. In total, 16 terminations have occurred. A electrical component with 4 channels is capable of high-quality output. An 15V voltage supply should allow the electrical part to be turned on and run. A total of 16 pins are injected into the electrical part body. A SPST - NC switching circuit is used for these analog switches. If you are looking for variants of the digital switch, trying search with ADG211. This digital multiplexer has 115Ohm internal resistance. Datasheets for 16 pin functions are available upon request. There is Multiplexer or Switches analog multiplexer like this in the world. A voltage higher than 25V should not normally be supplied to the switches. Analogue multiplexers of the Dual supply type that are cost-effective. The switch multiplexer may be damaged if it is exposed to voltage greater than 1mA. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 22V. It can operate from 5V operating voltages.
ADG211AKRZ Features
4 Channels
Switch Circuit: SPST - NC
ADG211AKRZ Applications
There are a lot of Analog Devices Inc. ADG211AKRZ Analog Switches & Multiplexers ICs applications.
- Automatic test equipment
- Multiplexers
- Residential Gateways, Home Gateway/Router
- Isolation
- High reliability control systems
- Relay Replacement
- Microprocessor controlled systems
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- PBXs
- Microprocessor Controlled Analog Systems
