ADG212AKR
| Parameters | |
|---|---|
| Contact Plating | Lead, Tin |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 115Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | ADG212 |
| Pin Count | 16 |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Number of Channels | 4 |
| Interface | Parallel |
| Max Supply Voltage | 25V |
| Nominal Supply Current | 100μA |
| Power Dissipation | 22.5mW |
| Max Supply Current | 1mA |
| Throw Configuration | SPST |
| Turn On Delay Time | 600 ns |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 450 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 115Ohm |
| High Level Output Current | 30mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 80 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 600ns, 450ns |
| Charge Injection | 20pC |
| Channel-to-Channel Matching (ΔRon) | 5.75 Ω |
| Crosstalk | -80dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Voltage - Supply, Dual (V±) | ±15V |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG212AKR Overview
The electronic component is convenient to ship overseas because it is packed in a 16-SOIC (0.154, 3.90mm Width). High reliability is provided by advanced packaging method Tube. Surface Mount is where this multiplexer is located. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Increasing operating temperature to around -40°C~85°C TA. In total, there are 16 terminations. The electronic part delivers high-quality output through its 4 channels. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. As part of the design of the 16 series, this electronic part has been incorporated into the system. Circuits based on SPST - NO switching are used to construct these analog switch ics. Try searching for the analog switch ic with ADG212 if you are looking for variants. The internal resistance of this digital multiplexer is 115Ohm. Please refer to the datasheets for 16 pins functions. The analogue multiplexer in this example is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 25V to the switch device in normal circumstances. Digital switch that provides Dual power at a cost-effective price. When the digital multiplexer is charged above 1mA, damage can occur. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 22V. The electronic component can function from 5V.
ADG212AKR Features
4 Channels
Switch Circuit: SPST - NO
ADG212AKR Applications
There are a lot of Analog Devices Inc. ADG212AKR Analog Switches & Multiplexers ICs applications.
- PDAs
- Power routing
- Wireless Local Loop
- Multiplexers
- DVD-R
- Cable Modem
- Automatic test equipment
- Intelligent PBX
- Audio and video switching
- ISDN NT1/TA
