ADG221KNZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 week ago) |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 90Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 25.5mW |
| Technology | CMOS |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Base Part Number | ADG221 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 15V |
| Number of Channels | 4 |
| Interface | Parallel |
| Max Supply Voltage | 25V |
| Nominal Supply Current | 1.5mA |
| Power Dissipation | 25.5mW |
| Max Supply Current | 1.5mA |
| Throw Configuration | SPST |
| Turn On Delay Time | 300 ns |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 90Ohm |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 80 dB |
| Current - Leakage (IS(off)) (Max) | 2nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 350ns, 250ns |
| Charge Injection | 20pC |
| Channel-to-Channel Matching (ΔRon) | 4.5 Ω |
| Crosstalk | -80dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 90Ohm |
| Normal Position | NC |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 3.3mm |
| Length | 20.07mm |
| Width | 6.35mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG221KNZ Overview
Shipping overseas is convenient due to the electrical component's packing in 16-DIP (0.300, 7.62mm). This high-reliability packaging method uses advanced packaging methods Tube. Through Hole is where this multiplexer is located. 1:1 is the number of circuits in the multiplexer and demultiplexer. The operating temperature is extended to around -40°C~85°C TA. In total, there are 16 terminations. A high-quality output is provided by the electrical component's 4 channels. Turning on and running the electrical part should be easy with a 15V voltage supply. The electronic part body is injected with 16 pins. Multiplexers built on a SPST - NC switching circuit are built. Try searching for ADG221 variants of the analog switch ic. In this multiplexer, the internal resistance is 90Ohm. Datasheets for functions of 16 pins are available. There is Multiplexer or Switches analog multiplexer like this in the world. A voltage higher than 25V should not normally be supplied to the switches. A analog switch ic that has a cost-effective Dual supply type. A voltage higher than 1.5mA may cause damage to the switch multiplexer. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 22V. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. This electrical part is compatible with 15V operating voltages. There is 90Ohm resistance between Drain and Source for this electronic part.
ADG221KNZ Features
4 Channels
Switch Circuit: SPST - NC
Drain-to-Source resistance: 90Ohm
ADG221KNZ Applications
There are a lot of Analog Devices Inc. ADG221KNZ Analog Switches & Multiplexers ICs applications.
- Fiber to the Home
- Low-Voltage
- Cross Connects
- FTTH
- Relay replacements
- Digital cross connects (DSX-1)
- Video signal routing
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Precision data acquisition
- Audio and video switching
