ADG221KR
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 90Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 25.5mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG221 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 15V |
| Number of Channels | 4 |
| Max Supply Voltage | 25V |
| Power Dissipation | 25.5mW |
| Max Supply Current | 1.5mA |
| Throw Configuration | SPST |
| Turn On Delay Time | 300 ns |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 90Ohm |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 80 dB |
| Current - Leakage (IS(off)) (Max) | 2nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 350ns, 250ns |
| Charge Injection | 20pC |
| Channel-to-Channel Matching (ΔRon) | 4.5 Ω |
| Crosstalk | -80dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Voltage - Supply, Dual (V±) | ±15V |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG221KR Overview
Packed in 16-SOIC (0.154, 3.90mm Width), the electronic component is convenient for shipping overseas. High reliability is ensured by the advanced packaging method Tube. Mounted in Surface Mount is this multiplexer. 1:1 is the ratio between multiplexers and demultiplexers. Around -40°C~85°C TA is the extended operating temperature. Totally, there are 16 terminations. As a result of its 4 channels, this electronic component provides high-quality output. When the electronic component is given a voltage of 15V, it should be turned on and run. A total of 16 pins are injected into the body of the electronic part. Multiplexers built on a SPST - NC switching circuit are built. Using the ADG221 search parameter, you can discover variants of the switch. A 90Ohm internal resistance characterizes this multiplexer. To find out what the 16 pins do, please refer to the datasheets. Multiplexer or Switches is a typical switch device. It is normally recommended that users do not supply the multiplexer with voltages higher than 25V. Analogue multiplexers of the Dual supply type that are cost-effective. If put voltage greater than 1.5mA on the device, damage may be caused to the analogue multiplexer. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 22V. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. It can operate from 15V operating voltages.
ADG221KR Features
4 Channels
Switch Circuit: SPST - NC
ADG221KR Applications
There are a lot of Analog Devices Inc. ADG221KR Analog Switches & Multiplexers ICs applications.
- Relay replacements
- Switching Systems
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Communications systems
- DSLAMs
- RGB switches
- Cable PC
- High speed data transmission line cards
- Avionics and Military Systems
- Fiber In The Loop (FITL)
