ADG333ABN
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 20-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Resistance | 45Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 3.77mW |
| Technology | BICMOS |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Base Part Number | ADG333 |
| Pin Count | 20 |
| Number of Outputs | 8 |
| Operating Supply Voltage | 12V |
| Number of Channels | 4 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 3V |
| Power Dissipation | 3.77mW |
| Max Supply Current | 250μA |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 3V~30V ±3V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 45Ohm |
| Min Dual Supply Voltage | 3V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 7pF |
| On-state Resistance Match-Nom | 4Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 90ns, 80ns (Typ) |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 5 Ω |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Height Seated (Max) | 5.33mm |
| Length | 25.2mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG333ABN Overview
Packed in 20-DIP (0.300, 7.62mm), the electronic component is convenient for shipping overseas. High reliability is ensured by the advanced packaging method Tube. In Through Hole, this analog switch is mounted. Multiplexers and demultiplexers have a number of circuits 2:1. Operation at a temperature around -40°C~85°C TA. Total terminations are 20. The electronic part delivers high-quality output through its 4 channels. When a voltage supply of 15V is used, the electronic component should be turned on and run. It is injected into the electrical part body with 20 pins. Multiplexers built on a SPDT switching circuit are built. Try searching for ADG333 variants of the analog switch ic. Analog switches have 45Ohm internal resistance. For functions related to 20 pins, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. A voltage higher than 30V should not normally be supplied to the switches. A cost-effective Dual, Single supply type analogue multiplexer. There should be 3V voltage fed to the electrical part below 3V. Put voltage above 250μA on the multiplexer to cause damage. Despite this switch device's dual supply capability, its voltage should not exceed 20V. You should attach at least 3V voltage if you are using dual power supply. It can operate from 12V operating voltages. The analogue multiplexer has 8 outputs.
ADG333ABN Features
4 Channels
Switch Circuit: SPDT
ADG333ABN Applications
There are a lot of Analog Devices Inc. ADG333ABN Analog Switches & Multiplexers ICs applications.
- High reliability control systems
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Cable Modem
- Optical Applications
- Microprocessor Controlled Analog Systems
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Battery-powered systems
- Fault Tolerant Systems
- SDH
- Multiplexers
