Parameters |
Mounting Type |
Surface Mount |
Package / Case |
20-SSOP (0.209, 5.30mm Width) |
Surface Mount |
YES |
Number of Pins |
20 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
20 |
ECCN Code |
EAR99 |
Resistance |
45Ohm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
3.77mW |
Technology |
BICMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
235 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
0.65mm |
Time@Peak Reflow Temperature-Max (s) |
20 |
Base Part Number |
ADG333 |
Pin Count |
20 |
Number of Outputs |
8 |
Operating Supply Voltage |
12V |
Number of Channels |
4 |
Interface |
Parallel |
Max Supply Voltage |
30V |
Min Supply Voltage |
3V |
Test Frequency |
1MHz |
Power Dissipation |
3.77mW |
Max Supply Current |
250μA |
Turn On Delay Time |
175 ns |
Voltage - Supply, Single/Dual (±) |
3V~30V ±3V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
145 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
45Ohm |
Min Dual Supply Voltage |
3V |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
72 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
7pF |
On-state Resistance Match-Nom |
4Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
90ns, 80ns (Typ) |
Charge Injection |
2pC |
Channel-to-Channel Matching (ΔRon) |
5 Ω |
Crosstalk |
-85dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Height Seated (Max) |
2mm |
Length |
7.2mm |
Width |
5.3mm |
Radiation Hardening |
No |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
ADG333ABRS Overview
Presented in 20-SSOP (0.209, 5.30mm Width), this electrical component is convenient for overseas shipping. This packaging method provides high reliability because it uses advanced packaging techniques. Multiplexers like this are mounted in the Surface Mount position. Multiplexers and demultiplexers have the same number of circuits 2:1. Operating temperature extended to -40°C~85°C TA. A total of 20 terminations have been recorded. This electronic part offers high-quality output due to its 4 channels. It is safe to turn on and run the electronic component with a 15V voltage supply. 20 pins are injected to the electronic part body. Multiplexers built on a SPDT switching circuit are built. Try searching for ADG333 variants of the analog switch ic. Internally, this switch multiplexer has a resistance of 45Ohm. Please refer to the datasheets for 20 pins functions. Theswitch device is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 30V to the switch device in normal circumstances. An effective Dual, Single supply digital multiplexer. It is recommended that the electrical component receives a voltage of 3V. The analogue multiplexer may be damaged if voltage is greater than 250μA. There is no problem with using dual supply voltage, but it should not exceed 20V. The voltage should be at least 3V if you are using dual power supplies. It can operate from 12V operating voltages. In this digital multiplexer, there are 8 outputs.
ADG333ABRS Features
4 Channels
Switch Circuit: SPDT
ADG333ABRS Applications
There are a lot of Analog Devices Inc. ADG333ABRS Analog Switches & Multiplexers ICs applications.
- FTTH
- Channelized and Unchannelized DS3 applications
- Audio signal routing
- Ultrasound
- 65 V DACs
- CSU
- Sample-and-hold systems
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Battery-powered systems
- Battery Powered Instruments