ADG333ABRS-REEL

90ns, 80ns (Typ) SPDT 45Ohm Analog Switches BREAK-BEFORE-MAKE ADG333 20 Pins 250pA 15V 20-SSOP (0.209, 5.30mm Width)

Manufacturer: Analog Devices Inc.
Nocochips NO: 84-ADG333ABRS-REEL
Package: 20-SSOP (0.209, 5.30mm Width)
Datasheet: PDF
Stock: 103
Description: 90ns, 80ns (Typ) SPDT 45Ohm Analog Switches BREAK-BEFORE-MAKE ADG333 20 Pins 250pA 15V 20-SSOP (0.209, 5.30mm Width)(Kg)

Details

Tags

Parameters
Mounting Type	Surface Mount
Package / Case	20-SSOP (0.209, 5.30mm Width)
Surface Mount	YES
Number of Pins	20
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
JESD-609 Code	e0
Pbfree Code	no
Part Status	Obsolete
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	20
ECCN Code	EAR99
Resistance	45Ohm
Subcategory	Multiplexer or Switches
Max Power Dissipation	3.77mW
Technology	BICMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	240
Number of Functions	4
Supply Voltage	15V
Terminal Pitch	0.65mm
Reach Compliance Code	not_compliant
Time@Peak Reflow Temperature-Max (s)	30
Base Part Number	ADG333
Pin Count	20
Number of Outputs	8
Qualification Status	Not Qualified
Operating Supply Voltage	12V
Number of Channels	4
Interface	Parallel
Max Supply Voltage	30V
Min Supply Voltage	3V
Test Frequency	1MHz
Operating Supply Current	50nA
Power Dissipation	3.77mW
Max Supply Current	250μA
Turn On Delay Time	175 ns
Voltage - Supply, Single/Dual (±)	3V~30V ±3V~20V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	145 ns
Max Dual Supply Voltage	20V
On-State Resistance (Max)	45Ohm
Min Dual Supply Voltage	3V
Dual Supply Voltage	15V
Multiplexer/Demultiplexer Circuit	2:1
Off-state Isolation-Nom	72 dB
Current - Leakage (IS(off)) (Max)	250pA
Channel Capacitance (CS(off), CD(off))	7pF
On-state Resistance Match-Nom	4Ohm
Switch Circuit	SPDT
Switch Time (Ton, Toff) (Max)	90ns, 80ns (Typ)
Charge Injection	2pC
Channel-to-Channel Matching (ΔRon)	5 Ω
Crosstalk	-85dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Height Seated (Max)	2mm
Length	7.2mm
Width	5.3mm
RoHS Status	Non-RoHS Compliant
Lead Free	Contains Lead

ADG333ABRS-REEL Overview

Shipping overseas is convenient with the electronic component packed in 20-SSOP (0.209, 5.30mm Width). In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. A switch device like this is mounted in Surface Mount. 2:1 is the ratio between multiplexers and demultiplexers. Operational temperature extended around -40°C~85°C TA. 20 terminations have been made so far. The electronic part provides high-quality output because it has 4 channels. With a 15V voltage supply, the electrical component should be turned on and run. As part of the design of the 20 series, this electronic part has been incorporated into the system. A SPDT switching circuit is used to build these analog multiplexers. Search with ADG333 if you are looking for analog multiplexer variants. A 45Ohm internal resistance characterizes this multiplexer. The functions of 20 pins can be found in the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 30V volts for the multiplexer. A cost-effective Dual, Single supply type analogue multiplexer. There should be 3V voltage fed to the electrical part below 3V. It would be sufficient to run this analogue multiplexer with 50nA current. Putting voltage greater than 250μA on the multiplexer may cause damage. For this switch, a dual supply voltage is feasible, but it must not exceed 20VIf you are using a dual power supply, you should attach at least 3V. 12V operating voltages can be used with this electrical part. There are 8 outputs on the analogue multiplexer.