Parameters |
Switch Time (Ton, Toff) (Max) |
90ns, 80ns (Typ) |
Charge Injection |
2pC |
Channel-to-Channel Matching (ΔRon) |
5 Ω |
Crosstalk |
-85dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Height |
1.85mm |
Length |
7.5mm |
Width |
5.6mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 1 week ago) |
Mounting Type |
Surface Mount |
Package / Case |
20-SSOP (0.209, 5.30mm Width) |
Surface Mount |
YES |
Number of Pins |
20 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e3 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
20 |
ECCN Code |
EAR99 |
Resistance |
45Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
3.77mW |
Technology |
BICMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
0.65mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
ADG333 |
Pin Count |
20 |
Number of Outputs |
8 |
Operating Supply Voltage |
12V |
Number of Channels |
4 |
Interface |
Parallel |
Max Supply Voltage |
30V |
Min Supply Voltage |
3V |
Test Frequency |
1MHz |
Operating Supply Current |
50nA |
Power Dissipation |
3.77mW |
Max Supply Current |
250μA |
Turn On Delay Time |
175 ns |
Voltage - Supply, Single/Dual (±) |
3V~30V ±3V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
145 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
45Ohm |
Min Dual Supply Voltage |
3V |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
72 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
7pF |
On-state Resistance Match-Nom |
4Ohm |
Switch Circuit |
SPDT |
ADG333ABRSZ-REEL Overview
The electronic part can be shipped overseas conveniently because it is packaged in 20-SSOP (0.209, 5.30mm Width). Advanced packaging method Tape & Reel (TR) is used to provide high reliability. In Surface Mount, this analog switch is mounted. Multiplexer and demultiplexer circuits have a number 2:1. Operating temperature extended to -40°C~85°C TA. In total, there have been 20 terminations. This electronic part offers high-quality output due to its 4 channels. A 15V voltage supply should turn on and run the electronic component. It is injected into the electrical part body with 20 pins. Based on SPDT switching circuits, these analog multiplexers work. Try searching for the analog switch ic with ADG333 if you are looking for variants. A 45Ohm internal resistance characterizes this multiplexer. Datasheets for functions of 20 pins are available. This switch device is a typical Multiplexer or Switches. A voltage higher than 30V should not normally be supplied to the switches. Digital switch that provides Dual, Single power at a cost-effective price. A low voltage of 3V should be applied to the electronic component. It would be sufficient to run this analogue multiplexer with 50nA current. It may damage the digital multiplexer if the voltage is higher than 250μA. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 20V. For dual power supplies, a voltage of at least 3V should be attached. A voltage of 12V can be used to operate the electronic component. There are 8 outputs on the analogue multiplexer.
ADG333ABRSZ-REEL Features
4 Channels
Switch Circuit: SPDT
50nA Supply Current
ADG333ABRSZ-REEL Applications
There are a lot of Analog Devices Inc. ADG333ABRSZ-REEL Analog Switches & Multiplexers ICs applications.
- Communication systems
- Intelligent PBX
- Digital Cross-Connects
- Medical
- Voice over IP/DSL – Integrated Access Devices, Smart
- Isolation
- Frame Relay Equipment
- Switching Systems
- Data Acquisition Systems
- Precision test equipment