ADG406BNZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Contact Plating | Tin |
| Mounting Type | Through Hole |
| Package / Case | 28-DIP (0.600, 15.24mm) |
| Surface Mount | NO |
| Number of Pins | 28 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 28 |
| ECCN Code | EAR99 |
| Resistance | 50Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 3.1mW |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Base Part Number | ADG406 |
| Pin Count | 28 |
| Number of Channels | 16 |
| Interface | Parallel |
| Number of Circuits | 1 |
| Max Supply Voltage | 25V |
| Min Supply Voltage | 12V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Operating Supply Current | 100μA |
| Nominal Supply Current | 100μA |
| Power Dissipation | 3.1mW |
| Max Supply Current | 200μA |
| Propagation Delay | 150 ns |
| Turn On Delay Time | 240 ns |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 110 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 80Ohm |
| High Level Output Current | 20mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 16:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 50pF |
| On-state Resistance Match-Nom | 4Ohm |
| Switch Time (Ton, Toff) (Max) | 160ns, 150ns |
| Charge Injection | 8pC |
| Channel-to-Channel Matching (ΔRon) | 4 Ω |
| Crosstalk | -85dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 50Ohm |
| Signal Current-Max | 0.02A |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 4.95mm |
| Length | 39.75mm |
| Width | 14.73mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG406BNZ Overview
As the electronic part is packed in 28-DIP (0.600, 15.24mm), international shipping is convenient. The advanced packaging method Tube provides high reliability. A switch device like this is mounted in Through Hole. There is 16:1 ratio between the number of multiplexers and demultiplexers. Operational temperature extended around -40°C~85°C TA. Total terminations are 28. This electronic part offers high-quality output due to its 16 channels. Powered by a 15V voltage supply, the electrical part should be switched on and run. It is part of the design of the 28 series that this electronic component is included. 1 circuits are used in this analogue multiplexer. If you are looking for variants of the digital switch, trying search with ADG406. As far as internal resistance is concerned, it has 50Ohm. The functions of 28 pins can be found in the datasheets. It is a typical Multiplexer or Switches analog multiplexer. A voltage higher than 25V should not normally be supplied to the switches. It is recommended to use 12V as the lowest voltage for the electrical part. This multiplexer would work with 100μA current. If you put voltage higher than 200μA on the digital multiplexer, damage may occur. For this multiplexer, dual supply voltage is feasible, but it should not exceed 22V. There is an integrated analog IC SINGLE-ENDED MULTIPLEXER in the module. Resistivity from Drain to Source is 50Ohm for this electronic part.
ADG406BNZ Features
16 Channels
100μA Supply Current
Drain-to-Source resistance: 50Ohm
ADG406BNZ Applications
There are a lot of Analog Devices Inc. ADG406BNZ Analog Switches & Multiplexers ICs applications.
- Digital cross connects (DSX-1)
- Relay Replacement
- Power routing
- Switching Systems
- Precision test equipment
- SDH/SONET multiplexers
- PDH Multiplexers
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Audio and video signal routing
- Cell phones
