ADG407BP
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 28-LCC (J-Lead) |
| Surface Mount | YES |
| Number of Pins | 28 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 28 |
| ECCN Code | EAR99 |
| Resistance | 80Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 3.1mW |
| Technology | BICMOS |
| Terminal Position | QUAD |
| Terminal Form | J BEND |
| Peak Reflow Temperature (Cel) | 225 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | ADG407 |
| Pin Count | 28 |
| Operating Supply Voltage | 12V |
| Supply Voltage-Min (Vsup) | 13.5V |
| Number of Channels | 8 |
| Interface | Parallel |
| Number of Circuits | 2 |
| Max Supply Voltage | 25V |
| Analog IC - Other Type | DIFFERENTIAL MULTIPLEXER |
| Operating Supply Current | 100μA |
| Power Dissipation | 3.1mW |
| Max Supply Current | 200μA |
| Propagation Delay | 150 ns |
| Turn On Delay Time | 240 ns |
| Number of Inputs | 16 |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 110 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 80Ohm |
| High Level Output Current | 20mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 25pF |
| On-state Resistance Match-Nom | 4Ohm |
| Switch Time (Ton, Toff) (Max) | 160ns, 150ns |
| Charge Injection | 8pC |
| Channel-to-Channel Matching (ΔRon) | 4 Ω |
| Crosstalk | -85dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Neg Supply Voltage-Min (Vsup) | -13.5V |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 3.94mm |
| Length | 11.58mm |
| Width | 11.58mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG407BP Overview
The electronic component is convenient to ship overseas because it is packed in a 28-LCC (J-Lead). A high level of reliability can be achieved through the use of an advanced packaging method Tube. A switch device like this is mounted in Surface Mount. 8:1 is the ratio between multiplexers and demultiplexers. Extended operating temperature around -40°C~85°C TA. A total of 28 terminations have been recorded. A 8 channel electronic part produces high-quality output. With a 15V voltage supply, the electrical component should be turned on and run. There are 28 pins injected into the electronic part body. The multiplexer consists of 2 circuits. If you are looking for variants of the digital switch, trying search with ADG407. In this multiplexer, the internal resistance is 80Ohm. Please refer to the datasheets for 28 pins functions. A analogue multiplexer of this type is a Multiplexer or Switches. Users should never supply a voltage higher than 25V to a switch device. For this multiplexer to operate, 100μA current would be sufficient. If you put voltage higher than 200μA on the digital multiplexer, damage may occur. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 22V. A DIFFERENTIAL MULTIPLEXER analog IC is integrated into the board. There is a voltage range of 12V operating voltages for the electrical part. Among the inputs that can be operated are the 16 inputs. In order to power the analogue multiplexer, it requires an input voltage of 13.5V volts.
ADG407BP Features
8 Channels
100μA Supply Current
ADG407BP Applications
There are a lot of Analog Devices Inc. ADG407BP Analog Switches & Multiplexers ICs applications.
- Audio and video routing
- Multi-Line E1 Interface Cards
- Fiber to the Home
- Cable Modem
- Communication systems
- Fiber In The Loop (FITL)
- Data Acquisition Systems
- Frame Relay Equipment
- Fault Tolerant Systems
- Multiplexers
