ADG408BN
| Parameters | |
|---|---|
| Contact Plating | Lead, Tin |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Base Part Number | ADG408 |
| Pin Count | 16 |
| Operating Supply Voltage | 12V |
| Number of Channels | 8 |
| Interface | Parallel |
| Number of Circuits | 1 |
| Max Supply Voltage | 32V |
| Min Supply Voltage | 5V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Operating Supply Current | 100μA |
| Power Dissipation | 3.1mW |
| Max Supply Current | 200μA |
| Throw Configuration | DPST |
| Propagation Delay | 130 ns |
| Turn On Delay Time | 140 ns |
| Number of Inputs | 8 |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 60 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 100Ohm |
| High Level Output Current | 20mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 11pF 40pF |
| On-state Resistance Match-Nom | 15Ohm |
| Charge Injection | 20pC |
| Channel-to-Channel Matching (ΔRon) | 15 Ω (Max) |
| Crosstalk | -85dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.02A |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 3.3mm |
| Length | 20.07mm |
| Width | 6.35mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG408BN Overview
Due to its 16-DIP (0.300, 7.62mm) packaging, the electronic part is convenient for international shipping. High reliability is provided by advanced packaging method Tube. Mounted in Through Hole is this multiplexer. There is 8:1 ratio between the number of multiplexers and demultiplexers. Increasing operating temperature to around -40°C~85°C TA. In total, 16 terminations have occurred. A high-quality output is provided by the electrical component's 8 channels. Turning on and running the electrical part should be easy with a 15V voltage supply. The electrical component body receives 16 pins. A 1 circuit is present in this switch device. Try searching for ADG408 variants of the analog switch ic. In this multiplexer, the internal resistance is 100Ohm. For functions related to 16 pins, please refer to the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 32V volts for the multiplexer. 5V is the lowest voltage that should be fed to the electronic electronic part. For this digital switch to work, 100μA current would suffice. A digital multiplexer may suffer damage if voltage is applied above 200μA. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 22V. A SINGLE-ENDED MULTIPLEXER analog IC is integrated into the board. Operating voltages range from 12V. Operating 8 inputs is required.
ADG408BN Features
8 Channels
100μA Supply Current
ADG408BN Applications
There are a lot of Analog Devices Inc. ADG408BN Analog Switches & Multiplexers ICs applications.
- SDH/SONET multiplexers
- Low-Voltage
- FTTH
- Automatic test equipment
- E1 Multiplexer
- Microprocessor Controlled Analog Systems
- PDH Multiplexers
- ISDN NT1/TA
- Digital Cross-Connects
- Cable PC
