ADG408BNZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Contact Plating | Tin |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Base Part Number | ADG408 |
| Pin Count | 16 |
| Operating Supply Voltage | 12V |
| Number of Channels | 8 |
| Interface | Parallel |
| Number of Circuits | 1 |
| Max Supply Voltage | 32V |
| Min Supply Voltage | 5V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Operating Supply Current | 100μA |
| Nominal Supply Current | 100μA |
| Power Dissipation | 3.1mW |
| Max Supply Current | 200μA |
| Throw Configuration | DPST |
| Propagation Delay | 130 ns |
| Turn On Delay Time | 225 ns |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 100Ohm |
| High Level Output Current | 20mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 11pF 40pF |
| On-state Resistance Match-Nom | 15Ohm |
| Charge Injection | 20pC |
| Channel-to-Channel Matching (ΔRon) | 15 Ω (Max) |
| Crosstalk | -85dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 40Ohm |
| Signal Current-Max | 0.02A |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 3.3mm |
| Length | 20.07mm |
| Width | 6.35mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG408BNZ Overview
The electrical component comes in 16-DIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. A high level of reliability can be achieved through the use of an advanced packaging method Tube. In Through Hole, you'll find this switch device. Multiplexers and demultiplexers have a ratio of 8:1. An extended operating temperature of -40°C~85°C TA degrees Celsius. Total terminations are 16. The electronic part delivers high-quality output through its 8 channels. An 15V voltage supply should allow the electrical part to be turned on and run. This electronic part can be found in the 16 series. The circuits in this analogue multiplexer number 1. If you are looking for variants of the digital switch, trying search with ADG408. It has an internal resistance of 100Ohm. The functions of 16 pins can be found in the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. Users should never supply a voltage higher than 32V to a switch device. A low voltage of 5V should be applied to the electronic component. In order to operate this switch device, it would need a current of 100μA. It may damage the digital multiplexer if the voltage is higher than 200μA. Despite this switch device's dual supply capability, its voltage should not exceed 22V. Integrated with SINGLE-ENDED MULTIPLEXER analog IC. This electrical part is compatible with 12V operating voltages. The Drain to Source resistance of this electronic component is 40Ohm.
ADG408BNZ Features
8 Channels
100μA Supply Current
Drain-to-Source resistance: 40Ohm
ADG408BNZ Applications
There are a lot of Analog Devices Inc. ADG408BNZ Analog Switches & Multiplexers ICs applications.
- FTTH
- Channel Banks
- New designs requiring multiplexer functions
- Fault Tolerant Systems
- Cellular phones
- Battery-powered systems
- Medical systems
- PDAs
- Ultrasound
- ISDN NT1/TA
