ADG408BRU
| Parameters | |
|---|---|
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 450mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 235 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | ADG408 |
| Pin Count | 16 |
| Operating Supply Voltage | 12V |
| Number of Channels | 8 |
| Interface | Parallel |
| Number of Circuits | 1 |
| Max Supply Voltage | 32V |
| Min Supply Voltage | 5V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Operating Supply Current | 100μA |
| Power Dissipation | 3.1mW |
| Max Supply Current | 200μA |
| Throw Configuration | DPST |
| Propagation Delay | 130 ns |
| Turn On Delay Time | 140 ns |
| Number of Inputs | 8 |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 60 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 100Ohm |
| High Level Output Current | 20mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 11pF 40pF |
| On-state Resistance Match-Nom | 15Ohm |
| Charge Injection | 20pC |
| Channel-to-Channel Matching (ΔRon) | 15 Ω (Max) |
| Crosstalk | -85dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.02A |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 1.05mm |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Contact Plating | Lead, Tin |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
ADG408BRU Overview
Shipping overseas is convenient due to the electrical component's packing in 16-TSSOP (0.173, 4.40mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tube. There is an analog multiplexer mounted in position Surface Mount. 8:1 is the ratio of multiplexer to demultiplexer circuits. An extended operating temperature of -40°C~85°C TA degrees Celsius. 16 terminations have been made so far. A high-quality output is provided by the electrical component's 8 channels. When the electronic component is given a voltage of 15V, it should be turned on and run. It is injected into the electrical part body with 16 pins. The multiplexer consists of 1 circuits. If you are looking for variants of the digital switch, trying search with ADG408. Internally, this switch multiplexer has a resistance of 100Ohm. Please refer to the datasheets for 16 pins functions. In this analog multiplexer, the value is Multiplexer or Switches. Users shouldn't supply more than 32V voltage to the switch device. 5V is the lowest voltage the electrical component should receive. This multiplexer would work with 100μA current. The analogue multiplexer may be damaged if voltage is greater than 200μA. For this multiplexer, dual supply voltage is feasible, but it should not exceed 22V. Integrated with an analog IC SINGLE-ENDED MULTIPLEXER. There is a voltage range of 12V operating voltages for the electrical part. There are 8 inputs to be operated.
ADG408BRU Features
8 Channels
100μA Supply Current
ADG408BRU Applications
There are a lot of Analog Devices Inc. ADG408BRU Analog Switches & Multiplexers ICs applications.
- Low-Voltage
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Battery Powered Instruments
- Avionics test equipment
- Medical
- Channelized and Unchannelized DS3 applications
- Sample hold systems
- Cable Modem
- Audio and video signal routing
- Automotive applications
