ADG408BRZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 600mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG408 |
| Pin Count | 16 |
| Operating Supply Voltage | 12V |
| Number of Channels | 8 |
| Interface | Parallel |
| Number of Circuits | 1 |
| Max Supply Voltage | 32V |
| Min Supply Voltage | 5V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Operating Supply Current | 100μA |
| Nominal Supply Current | 100μA |
| Power Dissipation | 3.1mW |
| Max Supply Current | 200μA |
| Throw Configuration | DPST |
| Propagation Delay | 130 ns |
| Turn On Delay Time | 225 ns |
| Number of Inputs | 8 |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 100Ohm |
| High Level Output Current | 20mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 11pF 40pF |
| On-state Resistance Match-Nom | 15Ohm |
| Charge Injection | 20pC |
| Channel-to-Channel Matching (ΔRon) | 15 Ω (Max) |
| Crosstalk | -85dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 40Ohm |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 1.5mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG408BRZ Overview
The electronic component is convenient to ship overseas because it is packed in a 16-SOIC (0.154, 3.90mm Width). High reliability is achieved by using advanced packaging method Tube. Multiplexers like this are mounted in the Surface Mount position. Multiplexers and demultiplexers have a number of circuits 8:1. Around -40°C~85°C TA is the extended operating temperature. In total, there have been 16 terminations. This electronic part offers high-quality output due to its 8 channels. It is safe to turn on and run the electronic component with a 15V voltage supply. It is injected into the electrical part body with 16 pins. There are 1 circuits in this multiplexer. Look for analog switch ic variants by searching with ADG408. A 100Ohm internal resistance characterizes this multiplexer. The functions of 16 pins can be found in the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. An abnormal situation would be for the switch device to be supplied with a voltage greater than 32V. 5V is the lowest voltage that should be fed to the electronic electronic part. This multiplexer would work with 100μA current. A digital multiplexer may suffer damage if voltage is applied above 200μA. For this switch, a dual supply voltage is feasible, but it must not exceed 22VAn analog IC with the number SINGLE-ENDED MULTIPLEXER is integrated into this board. The electronic component can function from 12V. The 8 inputs need to be operated in order to work. A Drain to Source resistance of 40Ohm is shown for this electronic part.
ADG408BRZ Features
8 Channels
100μA Supply Current
Drain-to-Source resistance: 40Ohm
ADG408BRZ Applications
There are a lot of Analog Devices Inc. ADG408BRZ Analog Switches & Multiplexers ICs applications.
- Fault Tolerant Systems
- Sample hold systems
- PDH Multiplexers
- Battery Powered Instruments
- Relay Replacement
- Fiber In The Loop (FITL)
- Multi-Line E1 Interface Cards
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Switching Systems
- Voice over IP/DSL – Integrated Access Devices, Smart
