Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 3 months ago) |
Contact Plating |
Tin |
Mounting Type |
Through Hole |
Package / Case |
16-DIP (0.300, 7.62mm) |
Surface Mount |
NO |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
JESD-609 Code |
e3 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
100Ohm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
470mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Number of Functions |
1 |
Supply Voltage |
15V |
Base Part Number |
ADG409 |
Pin Count |
16 |
Operating Supply Voltage |
12V |
Number of Channels |
4 |
Interface |
Parallel |
Number of Circuits |
2 |
Max Supply Voltage |
32V |
Min Supply Voltage |
5V |
Analog IC - Other Type |
DIFFERENTIAL MULTIPLEXER |
Operating Supply Current |
100μA |
Nominal Supply Current |
100μA |
Power Dissipation |
3.1mW |
Max Supply Current |
200μA |
Throw Configuration |
4PST |
Propagation Delay |
130 ns |
Turn On Delay Time |
225 ns |
Number of Inputs |
8 |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
150 ns |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
100Ohm |
High Level Output Current |
20mA |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
4:1 |
Off-state Isolation-Nom |
75 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
11pF 20pF |
On-state Resistance Match-Nom |
15Ohm |
Switch Circuit |
SP4T |
Charge Injection |
20pC |
Channel-to-Channel Matching (ΔRon) |
15 Ω (Max) |
Crosstalk |
-85dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Voltage - Supply, Dual (V±) |
±15V |
Height |
3.3mm |
Length |
20.07mm |
Width |
6.35mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
ADG409BNZ Overview
The electrical component comes in 16-DIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. This packaging method provides high reliability because it uses advanced packaging techniques. There is an analog multiplexer mounted in position Through Hole. There is 4:1 ratio between the number of multiplexers and demultiplexers. An extended operating temperature of -40°C~85°C TA degrees Celsius. In total, there have been 16 terminations. Due to its 4 channels, the electrical component produces high-quality output. A 15V voltage supply should turn on and run the electronic component. An electrical component like this is included in the 16 series. These analog multiplexers are built based on SP4T switching circuits. The circuits in this analogue multiplexer number 2. Search with ADG409 if you are looking for analog multiplexer variants. In this multiplexer, the internal resistance is 100Ohm. Datasheets for functions of 16 pins are available. There is Multiplexer or Switches analog multiplexer like this in the world. Multiplexers should not be powered above 32V in normal situations. The lowest voltage fed to the electronic component should be 5V. 100μA current would be enough for this multiplexer to operate. If put voltage greater than 200μA on the device, damage may be caused to the analogue multiplexer. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 22V. There is an analog IC DIFFERENTIAL MULTIPLEXER integrated with this board. The electronic component can function from 12V. There are 8 inputs to be operated.
ADG409BNZ Features
4 Channels
Switch Circuit: SP4T
100μA Supply Current
ADG409BNZ Applications
There are a lot of Analog Devices Inc. ADG409BNZ Analog Switches & Multiplexers ICs applications.
- Fiber to the Home
- Voice over IP/DSL – Integrated Access Devices, Smart
- Isolation
- Multiplexers
- Signal routing between systems
- ISDN NT1/TA
- Audio/video switches
- E1 Multiplexer
- Sample-and-hold systems
- Battery-powered systems