ADG409BRU
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG409 |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 12V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 32V |
| Analog IC - Other Type | DIFFERENTIAL MULTIPLEXER |
| Power Dissipation | 450mW |
| Throw Configuration | 4PST |
| Number of Inputs | 8 |
| Supply Current-Max (Isup) | 0.5mA |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 100Ohm |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 11pF 20pF |
| On-state Resistance Match-Nom | 15Ohm |
| Switch Circuit | SP4T |
| Charge Injection | 20pC |
| Channel-to-Channel Matching (ΔRon) | 15 Ω (Max) |
| Crosstalk | -85dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 150ns |
| Switch-off Time-Max | 150ns |
| Voltage - Supply, Dual (V±) | ±15V |
| Length | 5mm |
| Width | 4.4mm |
| RoHS Status | Non-RoHS Compliant |
ADG409BRU Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-TSSOP (0.173, 4.40mm Width). To ensure high reliability, a new packaging method Tube is used. In Surface Mount, you'll find this switch device. 4:1 is the ratio between multiplexers and demultiplexers. Operating temperature around -40°C~85°C TA extended. In total, there have been 16 terminations. A electrical component with 4 channels is capable of high-quality output. With a 15V voltage supply, the electrical component should be turned on and run. It is injected into the electrical part body with 16 pins. On the other hand, analog switches can be constructed using SP4T switching circuits. This multiplexer is composed of 2 circuits. Try searching with ADG409 if you're looking for variants. The internal resistance of this digital multiplexer is 100Ohm. Datasheets for functions of 16 pins are available. This switch device is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 32V to the switch device in normal circumstances. There is no problem with using dual supply voltage, but it should not exceed 22V. An analog IC with the number DIFFERENTIAL MULTIPLEXER is integrated into this board. 12V operating voltages are supported by the electronic component. Among the inputs that can be operated are the 8 inputs.
ADG409BRU Features
4 Channels
Switch Circuit: SP4T
ADG409BRU Applications
There are a lot of Analog Devices Inc. ADG409BRU Analog Switches & Multiplexers ICs applications.
- PBXs
- Remote Powered Equipment
- Ultrasound
- E1 Network Equipment
- Low-Voltage
- Power routing
- CSU
- Cable PC
- RGB switches
- Video signal routing
