ADG411BRU
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 35μW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG411 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 12V |
| Number of Channels | 4 |
| Interface | Parallel |
| Max Supply Voltage | 25V |
| Min Supply Voltage | 5V |
| Power Dissipation | 35μW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 13.5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 5pC |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Height Seated (Max) | 1.2mm |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG411BRU Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-TSSOP (0.173, 4.40mm Width). High reliability is achieved by using advanced packaging method Tube. There is an analog multiplexer mounted in position Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. The operating temperature is extended to around -40°C~85°C TA. In total, there are 16 terminations. By its 4 channels, the electronic component provides high-quality output. With a 15V voltage supply, the electrical component should be turned on and run. It is injected into the electrical part body with 16 pins. Based on SPST - NC switching circuits, these analog multiplexers work. Search with ADG411 if you are looking for analog multiplexer variants. The internal resistance of this digital multiplexer is 35Ohm. The functions of 16 pins can be found in the datasheets. Multiplexer or Switches is a typical switch device. An abnormal situation would be for the switch device to be supplied with a voltage greater than 25V. Analogue multiplexers of the Dual, Single supply type that are cost-effective. 5V is the lowest voltage that should be fed to the electronic electronic part. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. There is no problem with using dual supply voltage, but it should not exceed 22V. You should attach at least 13.5V voltage if you are using dual power supply. This analog switch ic utilizes SEPARATE OUTPUT output. Operating voltages of 12V are compatible with the electrical part.
ADG411BRU Features
4 Channels
Switch Circuit: SPST - NC
ADG411BRU Applications
There are a lot of Analog Devices Inc. ADG411BRU Analog Switches & Multiplexers ICs applications.
- Data Acquisition Systems
- Digital access cross connects
- SONET
- Channel Banks
- Imaging
- RGB switches
- PBXs
- Multiplexers
- Audio and video switching
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
