Parameters |
Contact Plating |
Lead, Tin |
Mounting Type |
Surface Mount |
Package / Case |
16-TSSOP (0.173, 4.40mm Width) |
Surface Mount |
YES |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
35Ohm |
Terminal Finish |
Tin/Lead (Sn85Pb15) |
Additional Feature |
ALSO OPERATE WITH 12V SINGLE SUPPLY |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
35μW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
0.65mm |
Reach Compliance Code |
not_compliant |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
ADG411 |
Pin Count |
16 |
Qualification Status |
Not Qualified |
Operating Supply Voltage |
12V |
Polarity |
Non-Inverting |
Number of Channels |
4 |
Interface |
Parallel |
Max Supply Voltage |
25V |
Min Supply Voltage |
5V |
Operating Supply Current |
100pA |
Power Dissipation |
35μW |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
175 ns |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
145 ns |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
35Ohm |
Min Dual Supply Voltage |
13.5V |
High Level Output Current |
30mA |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
68 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
9pF 9pF |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
175ns, 145ns |
Charge Injection |
5pC |
Crosstalk |
-85dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Normal Position |
NC |
Voltage - Supply, Dual (V±) |
±15V |
Height Seated (Max) |
1.2mm |
Length |
5mm |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
ADG411BRU-REEL7 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-TSSOP (0.173, 4.40mm Width). High reliability is achieved by using advanced packaging method Tape & Reel (TR). In Surface Mount, this analog switch is mounted. 1:1 is the number of circuits in the multiplexer and demultiplexer. Operation at a temperature around -40°C~85°C TA. The total number of terminations is 16. A 4 channel electronic part produces high-quality output. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. This electronic part can be found in the 16 series. A SPST - NC switching circuit is used to build these analog multiplexers. Look for analog switch ic variants by searching with ADG411. In this multiplexer, the internal resistance is 35Ohm. The datasheets for the 16 pins explain the functions. The analogue multiplexer in this example is a typical Multiplexer or Switches. Users should never supply a voltage higher than 25V to a switch device. Digital switch that provides Dual, Single power at a cost-effective price. A low voltage of 5V should be applied to the electronic component. This digital switch can be operated with a current of 100pA. It may damage the digital multiplexer if the voltage is higher than 1μA. There is no problem with using dual supply voltage, but it should not exceed 22V. It is recommended that you attach at least 13.5V to your dual power supply. A voltage of 12V can be used to operate the electronic component. There is also ALSO OPERATE WITH 12V SINGLE SUPPLY to look out for in this electronic part.
ADG411BRU-REEL7 Features
4 Channels
Switch Circuit: SPST - NC
100pA Supply Current
Additional Features: ALSO OPERATE WITH 12V SINGLE SUPPLY
ADG411BRU-REEL7 Applications
There are a lot of Analog Devices Inc. ADG411BRU-REEL7 Analog Switches & Multiplexers ICs applications.
- Multi-Line E1 Interface Cards
- Cable PC
- CSU
- MP3 players
- Low-Voltage
- Precision test equipment
- ATM
- Medical
- HDTV
- Data Acquisition Systems