ADG411BRZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 600mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG411 |
| Pin Count | 16 |
| Operating Supply Voltage | 12V |
| Polarity | Non-Inverting |
| Number of Channels | 4 |
| Interface | Parallel |
| Max Supply Voltage | 25V |
| Min Supply Voltage | 5V |
| Power Dissipation | 35μW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 13.5V |
| High Level Output Current | 30mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 5pC |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 25Ohm |
| Normal Position | NC |
| Height | 1.5mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG411BRZ Overview
Shipping overseas is convenient due to the electrical component's packing in 16-SOIC (0.154, 3.90mm Width). The advanced packaging method Tube provides high reliability. The multiplexer is located in Surface Mount. Multiplexer and demultiplexer circuits have a number 1:1. An extended operating temperature of -40°C~85°C TA degrees Celsius. 16 terminations have been made so far. The electronic part delivers high-quality output through its 4 channels. When the electronic component is given a voltage of 15V, it should be turned on and run. 16 pins are injected to the electronic part body. Multiplexers built on a SPST - NC switching circuit are built. Try searching for the analog switch ic with ADG411 if you are looking for variants. It has an internal resistance of 35Ohm. Datasheets for 16 pin functions are available upon request. This switch device is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 25V. An effective Dual, Single supply digital multiplexer. It is recommended to use 5V as the lowest voltage for the electrical part. Putting voltage greater than 1μA on the multiplexer may cause damage. Despite this switch device's dual supply capability, its voltage should not exceed 22V. For dual power supplies, a voltage of at least 13.5V should be attached. Operating voltages of 12V are compatible with the electrical part. Drain to Source resistance for this electronic component is 25Ohm.
ADG411BRZ Features
4 Channels
Switch Circuit: SPST - NC
Drain-to-Source resistance: 25Ohm
ADG411BRZ Applications
There are a lot of Analog Devices Inc. ADG411BRZ Analog Switches & Multiplexers ICs applications.
- HDTV
- Cable Modem
- Modems
- Industrial control systems
- Ultrasound
- DSUs
- Communications systems
- Central office
- Routers
- High-Voltage
