ADG412BRU-REEL7
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG412 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 12V |
| Number of Channels | 4 |
| Max Supply Voltage | 25V |
| Power Dissipation | 450mW |
| Throw Configuration | SPST |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 5pC |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 175ns |
| Normal Position | NO |
| Height Seated (Max) | 1.2mm |
| Length | 5mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG412BRU-REEL7 Overview
The electronic component is convenient to ship overseas because it is packed in a 16-TSSOP (0.173, 4.40mm Width). The advanced packaging method Tape & Reel (TR) provides high reliability. The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. Temperatures around -40°C~85°C TA are extended for operation. In total, 16 terminations have occurred. A 4 channel electronic part produces high-quality output. If the voltage supply is 15V volts, the electrical component should be turned on and run. An injection of 16 pins is performed into the body of the electrical component. Multiplexers built on a SPST - NO switching circuit are built. Use ADG412 to search for variants of the digital switches. An switch multiplexer with 35Ohm internal resistance has a value of 35Ohm. The datasheets for the 16 pins explain the functions. The analogue multiplexer in this example is a typical Multiplexer or Switches. Users shouldn't supply more than 25V voltage to the switch device. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 22V. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. 12V operating voltages are supported by the electronic component.
ADG412BRU-REEL7 Features
4 Channels
Switch Circuit: SPST - NO
ADG412BRU-REEL7 Applications
There are a lot of Analog Devices Inc. ADG412BRU-REEL7 Analog Switches & Multiplexers ICs applications.
- PCMCIA cards
- PDH Multiplexers
- Avionics test equipment
- Microprocessor controlled systems
- High speed data transmission line cards
- Fault Tolerant Systems
- Digital access cross connects
- Central office
- Fiber In The Loop (FITL)
- Residential Gateways, Home Gateway/Router
