Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 2 weeks ago) |
Mounting Type |
Surface Mount |
Package / Case |
16-TSSOP (0.173, 4.40mm Width) |
Surface Mount |
YES |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
JESD-609 Code |
e3 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
35Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
35μW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
0.65mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
ADG412 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Operating Supply Voltage |
12V |
Number of Channels |
1 |
Interface |
Parallel |
Max Supply Voltage |
25V |
Min Supply Voltage |
5V |
Power Dissipation |
35μW |
Max Supply Current |
1μA |
Turn On Delay Time |
175 ns |
Number of Inputs |
4 |
Voltage - Supply, Single/Dual (±) |
12V ±15V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
145 ns |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
35Ohm |
Min Dual Supply Voltage |
13.5V |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
68 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
9pF 9pF |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
175ns, 145ns |
Charge Injection |
5pC |
Crosstalk |
-85dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Normal Position |
NO |
Height |
1.2mm |
Length |
5.1mm |
Width |
4.5mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
ADG412BRUZ Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-TSSOP (0.173, 4.40mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. A switch device like this is mounted in Surface Mount. 1:1 is the number of circuits in the multiplexer and demultiplexer. Operating temperature around -40°C~85°C TA extended. Totally, there are 16 terminations. A high-quality output is provided by the electrical component's 1 channels. An 15V voltage supply should allow the electrical part to be turned on and run. There are 16 pins injected into the electronic part body. SPST - NO switching circuits are used in these analog switch ics. Try searching for ADG412 variants of the analog switch ic. It has an internal resistance of 35Ohm. Datasheets for functions of 16 pins are available. It is a typical Multiplexer or Switches analog multiplexer. It is normally recommended that users do not supply the multiplexer with voltages higher than 25V. Analogue multiplexer with a Dual, Single supply type that is cost-effective. The lowest voltage the electronic part should receive is 5V. When the digital multiplexer is charged above 1μA, damage can occur. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 22V. In the case of dual power supplies, you should connect at least 13.5V. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. It can operate from 12V operating voltages. A 4 input needs to be operated.
ADG412BRUZ Features
1 Channels
Switch Circuit: SPST - NO
ADG412BRUZ Applications
There are a lot of Analog Devices Inc. ADG412BRUZ Analog Switches & Multiplexers ICs applications.
- Precision data acquisition
- DSUs
- Data Acquisition Systems
- Relay Replacement
- Central office
- Low-Voltage
- SONET/SDH ADM
- High-Voltage
- Digital Cross-Connects
- Audio and video switching