ADG412BRUZ-REEL
| Parameters | |
|---|---|
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | ADG412 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 12V |
| Number of Channels | 1 |
| Max Supply Voltage | 25V |
| Min Supply Voltage | 5V |
| Power Dissipation | 35μW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 175 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 13.5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 5pC |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Height Seated (Max) | 1.2mm |
| Length | 5mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 35μW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
ADG412BRUZ-REEL Overview
Shipping overseas is convenient with the electronic component packed in 16-TSSOP (0.173, 4.40mm Width). High reliability is ensured by the advanced packaging method Tape & Reel (TR). A switch device like this is mounted in Surface Mount. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Temperatures around -40°C~85°C TA are extended for operation. 16 terminations have been made so far. The electronic part delivers high-quality output through its 1 channels. Powered by a 15V voltage supply, the electrical part should be switched on and run. As part of its design, the 16 series is equipped with this electronic component. SPST - NO switching circuits are used in these analog switch ics. Using the ADG412 search parameter, you can discover variants of the switch. This digital multiplexer has 35Ohm internal resistance. The functions of 16 pins can be found in the datasheets. Multiplexer or Switches is a typical switch device. A voltage higher than 25V should not normally be supplied to the switches. Dual, Single supply type digital switch with a low cost. There should be 5V voltage fed to the electrical part below 5V. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. For this multiplexer, dual supply voltage is feasible, but it should not exceed 22V. When using dual power supplies, you should attach at least 13.5V. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. It can operate from 12V operating voltages. Operating 4 inputs is required.
ADG412BRUZ-REEL Features
1 Channels
Switch Circuit: SPST - NO
ADG412BRUZ-REEL Applications
There are a lot of Analog Devices Inc. ADG412BRUZ-REEL Analog Switches & Multiplexers ICs applications.
- SDH/SONET multiplexers
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- HDTV
- Data Acquisition Systems
- Optical Applications
- Audio signal routing
- Remote Powered Equipment
- Audio and video switching
- Channelized and Unchannelized DS3 applications
- Cellular phones
