ADG412BRZ
| Parameters | |
|---|---|
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 600mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG412 |
| Pin Count | 16 |
| Operating Supply Voltage | 12V |
| Polarity | Non-Inverting |
| Number of Channels | 4 |
| Interface | Parallel |
| Max Supply Voltage | 25V |
| Min Supply Voltage | 5V |
| Power Dissipation | 35μW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 13.5V |
| High Level Output Current | 30mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 5pC |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 25mOhm |
| Normal Position | NO |
| Height | 1.5mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 months ago) |
ADG412BRZ Overview
This electronic part is conveniently packaged in 16-SOIC (0.154, 3.90mm Width), making it easy to ship abroad. High reliability is achieved by using advanced packaging method Tube. A switch device like this is mounted in Surface Mount. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. The operating temperature is extended to around -40°C~85°C TA. In total, 16 terminations have occurred. The electronic part provides high-quality output because it has 4 channels. With a 15V voltage supply, the electrical component should be turned on and run. It is part of the design of the 16 series that this electronic component is included. Multiplexers built on a SPST - NO switching circuit are built. ADG412 can be used to search for analog multiplexer variants. It has an internal resistance of 35Ohm. For details about the functions of 16 pins, please refer to the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. Multiplexers should not be powered above 25V in normal situations. Analog switch ics with Dual, Single supply type are cost-effective. 5V is the lowest voltage that should be fed to the electronic electronic part. A digital multiplexer may suffer damage if voltage is applied above 1μA. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 22V. The voltage should be at least 13.5V if you are using dual power supplies. The electrical part can be operated at 12V voltage levels. Drain to Source resistance is 25mOhm.
ADG412BRZ Features
4 Channels
Switch Circuit: SPST - NO
Drain-to-Source resistance: 25mOhm
ADG412BRZ Applications
There are a lot of Analog Devices Inc. ADG412BRZ Analog Switches & Multiplexers ICs applications.
- ATM
- Microprocessor controlled systems
- Power routing
- Precision data acquisition
- Medical
- Relay replacements
- Signal routing between systems
- Medical Instrumentation
- Low-Voltage
- Remote wireless modules
