Parameters |
Throw Configuration |
SPST |
Turn On Delay Time |
175 ns |
Voltage - Supply, Single/Dual (±) |
12V ±15V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
145 ns |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
35Ohm |
Min Dual Supply Voltage |
13.5V |
High Level Output Current |
30mA |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
68 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
9pF 9pF |
Switch Circuit |
SPST - NO/NC |
Switch Time (Ton, Toff) (Max) |
175ns, 145ns |
Charge Injection |
5pC |
Crosstalk |
-85dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Drain to Source Resistance |
25mOhm |
Height Seated (Max) |
1.75mm |
Length |
9.9mm |
Width |
3.9mm |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
Contact Plating |
Lead, Tin |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Surface Mount |
YES |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
35Ohm |
Terminal Finish |
Tin/Lead (Sn85Pb15) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
35μW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
235 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
1.27mm |
Reach Compliance Code |
not_compliant |
Time@Peak Reflow Temperature-Max (s) |
20 |
Base Part Number |
ADG413 |
Pin Count |
16 |
Qualification Status |
Not Qualified |
Operating Supply Voltage |
12V |
Polarity |
Non-Inverting |
Number of Channels |
4 |
Interface |
Parallel |
Max Supply Voltage |
25V |
Min Supply Voltage |
5V |
Power Dissipation |
35μW |
Max Supply Current |
1μA |
ADG413BR Overview
As the electronic part is packed in 16-SOIC (0.154, 3.90mm Width), international shipping is convenient. In order to provide high reliability, an advanced packaging method Tube is used. This analog switch is mounted in Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. Around -40°C~85°C TA is the extended operating temperature. 16 terminations have been made so far. This electronic part offers high-quality output due to its 4 channels. If the voltage supply is 15V volts, the electrical component should be turned on and run. The electronic part body is injected with 16 pins. Unlike digital switches, these are based on SPST - NO/NC switching circuits. Try searching with ADG413 if you're looking for variants. Analog switches have 35Ohm internal resistance. You can find the functions of the 16 pins in the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. Users should never supply a voltage higher than 25V to a switch device. Dual, Single supply type digital switch with a low cost. The lowest voltage the electronic part should receive is 5V. When the digital multiplexer is charged above 1μA, damage can occur. If put voltage greater than 22V on the multiplexer, damage may be caused to the device. The voltage should be at least 13.5V if you are using dual power supplies. There is a voltage range of 12V operating voltages for the electrical part. There is 25mOhm resistance between Drain and Source for this electronic part.
ADG413BR Features
4 Channels
Switch Circuit: SPST - NO/NC
Drain-to-Source resistance: 25mOhm
ADG413BR Applications
There are a lot of Analog Devices Inc. ADG413BR Analog Switches & Multiplexers ICs applications.
- Precision test equipment
- Digital cross connects (DSX-1)
- Ultrasound
- Industrial control systems
- Residential Gateways, Home Gateway/Router
- Sample-and-hold systems
- Sample hold systems
- HDTV
- Mechanical reed relay replacement
- PBX interfaces