Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 3 weeks ago) |
Contact Plating |
Tin |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Surface Mount |
YES |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
JESD-609 Code |
e3 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
35Ohm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
600mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
1.27mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
ADG413 |
Pin Count |
16 |
Operating Supply Voltage |
12V |
Polarity |
Non-Inverting |
Number of Channels |
4 |
Interface |
Parallel |
Max Supply Voltage |
25V |
Min Supply Voltage |
5V |
Power Dissipation |
35μW |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
175 ns |
Voltage - Supply, Single/Dual (±) |
12V ±15V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
145 ns |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
35Ohm |
Min Dual Supply Voltage |
13.5V |
High Level Output Current |
30mA |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
68 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
9pF 9pF |
Switch Circuit |
SPST - NO/NC |
Switch Time (Ton, Toff) (Max) |
175ns, 145ns |
Charge Injection |
5pC |
Crosstalk |
-85dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Drain to Source Resistance |
25Ohm |
Height |
1.5mm |
Length |
10mm |
Width |
4mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
ADG413BRZ Overview
As the electronic part is packed in 16-SOIC (0.154, 3.90mm Width), international shipping is convenient. High reliability is achieved by using advanced packaging method Tube. There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have the same number of circuits 1:1. Extended operating temperature around -40°C~85°C TA. 16 terminations have been made so far. A high-quality output is provided by the electrical component's 4 channels. A 15V voltage supply should turn on and run the electronic component. It is part of the design of the 16 series that this electronic component is included. Multiplexers built on a SPST - NO/NC switching circuit are built. If you are looking for variants of the digital switch, trying search with ADG413. Analog switches have 35Ohm internal resistance. To find out what the 16 pins do, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. Users should never supply a voltage higher than 25V to a switch device. A cost-effective Dual, Single supply type analogue multiplexer. The lowest voltage the electronic part should receive is 5V. When the digital multiplexer is charged above 1μA, damage can occur. If put voltage greater than 22V on the multiplexer, damage may be caused to the device. With dual power supplies, you should attach at least 13.5V. A voltage of 12V can be used to operate the electronic component. Drain to Source resistance is 25Ohm.
ADG413BRZ Features
4 Channels
Switch Circuit: SPST - NO/NC
Drain-to-Source resistance: 25Ohm
ADG413BRZ Applications
There are a lot of Analog Devices Inc. ADG413BRZ Analog Switches & Multiplexers ICs applications.
- SONET/SDH ADM
- Low-Voltage
- Battery Powered Instruments
- Relay Replacement
- Sample hold systems
- E1 Network Equipment
- Power routing
- High reliability control systems
- Routers
- Industrial