ADG417BNZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 35μW |
| Technology | CMOS |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Base Part Number | ADG417 |
| Pin Count | 8 |
| Operating Supply Voltage | 9V |
| Number of Channels | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 5V |
| Power Dissipation | 35μW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 160 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 100 ns |
| Max Dual Supply Voltage | 15V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 80 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 6pF 6pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 160ns, 100ns |
| Charge Injection | 7pC |
| Drain to Source Resistance | 25mOhm |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 3.43mm |
| Length | 9.27mm |
| Width | 7.24mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG417BNZ Overview
Shipping overseas is convenient due to the electrical component's packing in 8-DIP (0.300, 7.62mm). A high level of reliability can be achieved through the use of an advanced packaging method Tube. There is an analog multiplexer mounted in position Through Hole. 1:1 is the number of circuits in the multiplexer and demultiplexer. Increasing operating temperature to around -40°C~85°C TA. In total, there are 8 terminations. This electronic part offers high-quality output due to its 1 channels. A 15V voltage supply should turn on and run the electronic component. A total of 8 pins are injected into the electrical part body. Circuits based on SPST - NC switching are used to construct these analog switch ics. Try searching with ADG417 to find analog multiplexer variants. A 35Ohm internal resistance characterizes this multiplexer. The datasheets for the 8 pins explain the functions. Multiplexers should not be powered above 12V in normal situations. A analog switch ic that has a cost-effective Dual, Single supply type. A low voltage of 5V should be applied to the electronic component. Putting voltage greater than 1μA on the multiplexer may cause damage. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 15V. If you are using dual power supplies, you should attach at least 5V. Operating voltages of 9V are compatible with the electrical part. Resistivity from Drain to Source is 25mOhm for this electronic part.
ADG417BNZ Features
1 Channels
Switch Circuit: SPST - NC
Drain-to-Source resistance: 25mOhm
ADG417BNZ Applications
There are a lot of Analog Devices Inc. ADG417BNZ Analog Switches & Multiplexers ICs applications.
- Fault Tolerant Systems
- Sample hold systems
- FTTH
- SONET/SDH ADM
- PDAs
- Digital Cross-Connects
- Microprocessor Controlled Analog Systems
- Relay replacements
- Avionics test equipment
- Audio and video routing
